Black Decker CD 60 CRE - Инструкция по эксплуатации - Страница 4

4

ENGLISH

b.  Do not use the power tool if the switch 

does not turn it on and off. 

Any power tool 

that cannot be controlled with the switch is 
dangerous and must be repaired.

c.  Disconnect the plug from the power source 

and/or the battery pack from the power tool 
before making any adjustments, changing 
accessories, or storing power tools. 

Such 

preventive safety measures reduce the risk of 
starting the power tool accidentally.

d.  Store idle power tools out of the reach 

of children and do not allow persons 
unfamiliar with the power tool or these 
instructions to operate the power tool. 

Power tools are dangerous in the hands of 
untrained users.

e.  Maintain power tools. Check for 

misalignment or binding of moving parts, 
breakage of parts and any other condition 
that may affect the power tools operation. 
If damaged, have the power tool repaired 
before use. 

Many accidents are caused by 

poorly maintained power tools.

f.  Keep cutting tools sharp and clean. 

Properly 

maintained cutting tools with sharp cutting 
edges are less likely to bind and are easier to 
control.

g.  Use the power tool, accessories and 

tool bits etc., in accordance with these 
instructions, taking into account the 
working conditions and the work to 
be performed. 

Use of the power tool for 

operations different from those intended could 
result in a hazardous situation.

5. Service
a.  Have your power tool serviced by 

a qualifi ed repair person using only 
identical replacement parts. 

This will ensure 

that the safety of the power tool is maintained.

Additional power tool safety warnings 

Warning! 

Additional safety warnings for 

drills and impact drills

• 

Wear ear protectors with impact drills. 

Exposure to noise can cause hearing loss.

• 

Use auxiliary handles supplied with the tool. 

Loss of control can cause personal injury.

• 

Hold power tool by insulated gripping 
surfaces when performing an operation 
where the cutting accessory may contact 
hidden wiring or its own cord. 

Cutting 

accessory contacting a „live“ wire may make 
exposed metal parts of the power tool „live“ and 
shock the operator.

• 

Use clamps or another practical way to 
secure and support the workpiece to 
a stable platform. 

Holding the work by hand or 

against your body leaves it unstable and may 
lead to loss of control.

• 

Before drilling into walls, fl oors or ceilings, 
check for the location of wiring and pipes.

• 

Avoid touching the tip of a drill bit just after 
drilling, as it may be hot.

• 

This tool is not intended for use by persons 
(including children) with reduced physical, 
sensory or mental capabilities, or lack of 
experience and knowledge, unless they 
have been given supervision or instruction 
concerning use of the appliance by a person 
responsible for their safety. Children should be 
supervised to ensure that they do not play with 
the appliance.

• 

The intended use is described in this instruction 
manual. The use of any accessory or 
attachment or performance of any operation 
with this tool other than those recommended 
in this instruction manual may present a risk of 
personal injury and/or damage to property.

Vibration

The declared vibration emission values stated in 
the technical data and the declaration of conformity 
have been measured in accordance with a 
standard test method provided by EN 60745 and 
may be used for comparing one tool with another. 
The declared vibration emission value may also be 
used in a preliminary assessment of exposure.

Warning! 

The vibration emission value during 

actual use of the power tool can differ from the 
declared value depending on the ways in which 
the tool is used. The vibration level may increase 
above the level stated.

When assessing vibration exposure to determine 
safety measures required by 2002/44/EC to 
protect persons regularly using power tools in 
employment, an estimation of vibration exposure 
should consider, the actual conditions of use and 
the way the tool is used, including taking account 
of all parts of the operating cycle such as the times 
when the tool is switched off and when it is running 
idle in addition to the trigger time.