Ergomax AEG 412396 - Инструкция по эксплуатации - Страница 12

20

21

..................................750 W
..................................375 W
................ 0-1200/0-3400 min

-1

.........................750/2200 min

-1

..............................54400 min

-1

..............................36000 min

-1

...............................58/30 Nm
....................................20 mm
....................................22 mm
....................................13 mm
....................................16 mm
....................................40 mm
............................. 1,5-13 mm
............................1/2"x20 
....................................43 mm
...................................2,6 kg

....................................98 dB (A)
..................................109 dB (A)

...................................4,5 m/s

2

...................................1,5 m/s

2

....................................32 m/s

2

...................................6,4 m/s

2

ENGLISH

ENGLISH

TECHNICAL DATA

Rated input ..............................................................................
Output ......................................................................................
No-load speed, 1st gear/2nd gear ...........................................
Speed under load max., 1st gear/2nd gear .............................
Percussion rate........................................................................
Rate of percussion under load max. ........................................
Static jamming moment*, 1st gear/2nd gear ...........................
Drilling capacity in concrete .....................................................
Drilling capacity in brick and tile ..............................................
Drilling capacity in steel ...........................................................
Drilling capacity in Aluminium ..................................................
Drilling capacity in wood ..........................................................
Drill opening range ..................................................................
Drive shank..............................................................................
Chuck neck diameter ...............................................................
Weight without cable ...............................................................

Noise information

Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
  Sound pressure level (K = 3 dB(A)) .......................................
  Sound power level (K = 3 dB(A)) ............................................

Wear ear protectors!

Vibration information

Total vibration values (vector sum in the three axes) 
determined according to EN 60745.
Vibration emission value a

h

:

Drilling into metal .....................................................................
Uncertainty K ...........................................................................
Percussion drilling into concrete ..............................................
Uncertainty K ...........................................................................

 WARNING! Read all safety warnings and all 

instructions, including those given in the accompanying 

brochure

. Failure to follow the warnings and instructions 

may result in electric shock, ire and/or serious injury. 

Save all warnings and instructions for future reference. 

SAFETY INSTRUCTIONS

Wear ear protectors.

 Exposure to noise can cause hearing 

loss.

Use auxiliary handles supplied with the tool.

 Loss of 

control can cause personal injury.

Hold power tool by insulated gripping surfaces, when 

performing an operation where the cutting accessory 

may contact hidden wiring or its own cord.

 Contact with 

a „live“ wire will also make exposed metal parts of the power 
tool „live“ and shock the operator.
Appliances used at many different locations including open 
air should be connected via a residual current device of 
30 mA or less.
Always wear goggles when using the machine. It is 
recommended to wear gloves, sturdy non slipping shoes 
and apron. 

Sawdust and splinters must not be removed while the 
machine is running.
Always disconnect the plug from the socket before carrying 
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. 
Always lead the cable away behind you.
When working in 1st gear always use the bow-type handle 
and/or the auxialiarhandle. In case the machine is operated 
with the bow-type handle, the lower area of the motor 
housing might be used as auxiliary handle.
Do not use diamond core drills on hammer mode.

When working in walls ceiling, or loor, take care to avoid 

electric cables and gas or waterpipes.
The dust produced when using this tool may be harmful to 
health. Do not inhale the dust. Wear a suitable dust 
protection mask.

SPECIFIED CONDITIONS OF USE

The electronic drill/screwdriver can be universally used for 
drilling, percussion drilling, screwdriving and cutting screw 
threads.
Do not use this product in any other way as stated for 
normal use.

MAINS CONNECTION

Connect only to single-phase a.c. current and only to the 
system voltage indicated on the rating plate. It is also 
possible to connect to sockets without an earthing contact 
as the design conforms to safety class 

II

.

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is 
in conformity with the following standards or standardized 
documents. EN 60745, EN 55014-1, EN 55014-2, 
EN 61000-3-2, EN 61000-3-3, in accordance with the 
regulations 98/37/EC, 2004/108/EC

Rainer Kumpf

Manager Product Development

Winnenden, 2009-11-04

MAINTENANCE

The ventilation slots of the machine must be kept clear at all 
times.
If the machine is mainly used for percussion drilling, 
regularly remove collected dust from the chuck. To remove 
the dust hold the machine with the chuck facing down 
vertically, and completely open and close the chuck. The 
collected dust will fall from the chuck. It is recommended to 
regularly use cleaner for the clamping jaws and the 
clamping jaw borings.
Use only AEG accessories and spare parts. Should 
components need to be exchanged which have not been 
described, please contact one of our AEG service agents 
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. 
Please state the ten-digit No. as well as the machine type 
printed on the label and order the drawing at your local 
service agents or directly at: AEG Elektrowerkzeuge, 
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.

Measured values determined according to EN 60 745. 
The data stated above apply for models with 230 - 240 V. In case of deviating mains voltage, the data stated on the rating 
plate are applicable.
* Measured according to AEG norm N 877318

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given 
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different 

applications, with different accessories or poorly maintained, the vibration emission may differ. This may signiicantly increase 

the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or 

when it is running but not actually doing the job. This may signiicantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the 
accessories, keep the hands warm, organisation of work patterns.

SYMBOLS

Please read the instructions 
carefully before starting the 
machine.

Always disconnect the plug from the socket 
before carrying out any work on the 
machine.

Accessory - Not included in standard 
equipment, available as an accessory.

Do not dispose of electric tools together 
with household waste material! In 
observance of European Directive 2002/96/
EC on waste electrical and electronic 
equipment and its implementation in 
accordance with national law, electric tools 
that have reached the end of their   life 
must be collected separately and returned 
to an environmentally compatible recycling 
facility.