BSS18SBL-0 AEG 4935472278 - Инструкция по эксплуатации - Страница 20

20

 BSS18SBL 

BSS18S12BL

......................   4772 54 01... .................. 4772 61 01

   ...000001-999999 

...000001-999999

.......................... 1/4" (6,35 mm) ............... 1/2" (12,7 mm)

..................... 0-2900 min

-1

 ................... 0-2800 min

-1

..................... 0-4200 min

-1

 ................... 0-3800 min

-1

...........................200 Nm .......................... 280 Nm

..........................M14  ............................... M18 

.............................18 V ............................... 18 V

..................1,3 ... 2,0 kg ................... 1,4 ... 2,1 kg

........................................... -18...+50 °C

......................................L1815R, ... L1890R

....................... AL18G, AL1218G, BL1218, BLK1218

..........................96,0 dB  (A) ..................... 96,0 dB  (A)

........................107,0 dB  (A) ................... 107,0 dB  (A)

..........................13,0 m/s

2

 ........................... 13  m/s

2

............................1,5 m/s

2

 .......................... 1,5  m/s

2

ENGLISH

TECHNICAL DATA  CORDLESS IMPACT DRIVER / WRENCH

Production code...........................................................................

Tool reception ..............................................................................

No-load speed .............................................................................

Impact rate (high speed)..............................................................

Max. torque with battery 6.0 Ah ...................................................

Max. diameter bolt / nut ...............................................................

Battery voltage.............................................................................

Weight according EPTA-Procedure 01/2014 (1.5 Ah ... 9.0 Ah) ........

Recommended ambient operating temperature ..........................

Recommended battery types.......................................................

Recommended charger ...............................................................

Noise/vibration information

Measured values determined according to EN 62841.

Typically, the A-weighted noise levels of the tool are:

  Sound pressure level (Uncertainty K=3dB(A)) .........................

  Sound power level (Uncertainty K=3dB(A)) ..............................

Wear ear protectors!

Total vibration values (vector sum in the three axes) determined 

according to EN 62841.

Vibration emission value a

h 

  Impact tightening of fasteners of the maximum capacity of the tool 

 Uncertainty K= 

..........................................................................

 WARNING Read all safety warnings, instructions, 

illustrations and speci

fi

 cations provided with this power 

tool. 

Failure to follow all instructions listed below may result in 

electric shock, 

fi

 re and/or serious injury.

Save all warnings and instructions for future reference.

 IMPACT DRIVER / WRENCH SAFETY WARNINGS

Hold the power tool by insulated gripping surfaces, when 

performing an operation where the fastener may contact 

hidden wiring. 

Fasteners contacting a „live“ wire may make 

exposed metal parts of the power tool „live“ and could give the 

operator an electric shock.

Wear ear protectors.

 Exposure to noise can cause hearing 

loss.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Use protective equipment. Always wear safety glasses when 

working with the machine. The use of protective clothing is 

recommended, such as dust mask, protective gloves, sturdy 

non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to 

health. Do not inhale the dust. Wear a suitable dust protection 

mask.
Do not machine any materials that present a danger to health 

(e.g. asbestos).
Switch the device o

ff

  immediately if the insertion tool stalls! Do 

not switch the device on again while the insertion tool is stalled, 

as doing so could trigger a sudden recoil with a high reactive 

force. Determine why the insertion tool stalled and rectify this, 

paying heed to the safety instructions.
The possible causes may be:

•  it is tilted in the workpiece to be machined

•  it has pierced through the material to be machined

•  the power tool is overloaded

Do not reach into the machine while it is running.
The insertion tool may become hot during use.

WARNING! 

Danger of burns

•  when changing tools

•  when setting the device down
Chips and splinters must not be removed while the machine is 

running.
When working in walls ceiling, or 

fl

 oor, take care to avoid 

electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped 

workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the 

machine.
Do not dispose of used battery packs in the household refuse 

or by burning them. AEG Distributors o

ff

 er to retrieve old 

batteries to protect our environment.
Do not store the battery pack together with metal objects (short 

circuit risk).
Use only System GBS chargers for charging System GBS 

battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in 

dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme 

load or extreme temperatures. In case of contact with battery 

acid wash it o

ff

  immediately with soap and water. In case of eye 

contact rinse thoroughly for at least 10 minutes and 

immediately seek medical attention.

Warning! 

To reduce the risk of 

fi

 re, personal injury, and product 

damage due to a short circuit, never immerse your tool, battery 

pack or charger in 

fl

 uid or allow a 

fl

 uid to 

fl

 ow inside them. 

Corrosive or conductive 

fl

 uids, such as seawater, certain 

industrial chemicals, and bleach or bleach containing products, 

etc., can cause a short circuit.

WARNING

The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test 

given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for di

ff

 erent 

applications, with di

ff

 erent accessories or poorly maintained, the vibration and noise emission may di

ff

 er. This may signi

fi

 cantly 

increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched o

ff

  or 

when it is running but not actually doing the job. This may signi

fi

 cantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator from the e

ff

 ects of vibration and/or noise such as: maintain the tool and 

the accessories, keep the hands warm, organization of work patterns.

470 410 - BSS18SBL, BSS18S12BL_EN62841.indd   20

470 410 - BSS18SBL, BSS18S12BL_EN62841.indd   20

30.06.2020   12:45:17

30.06.2020   12:45:17