AEG BSS12G3 LI-202C 4935471061 - Инструкция по эксплуатации - Страница 12

12

BSS12G3

..................... 4699 85 01...

   ...000001-999999

.........................1/4" (6,35 mm)

....................0-2600 min

-1

....................0-3500 min

-1

......................... 130 Nm

........................ M14 

........................... 12 V

.............. 1,06...1,08 kg

.................-18...+50 °C

............... L1215G3, L1220G3

..............AL1214G3

........................... 95 dB (A)

......................... 106 dB (A)

........................... 12 m/s

2

.......................... 1,5 m/s

2

ENGLISH

TECHNICAL DATA 

CORDLESS IMPACT DRIVER

Production code......................................................................  

Tool reception .........................................................................

No-load speed ........................................................................

Impact range...........................................................................

Max. Torque ............................................................................  

Max. diameter bolt / nut. .........................................................

Battery voltage........................................................................

Weight according EPTA-Procedure 01/2014 (1.5...2.0 Ah) ....

Recommended ambient operating temperature .....................

Recommended battery types..................................................

Recommended charger ..........................................................

Noise/vibration information

Measured values determined according to EN 62841.

Typically, the A-weighted noise levels of the tool are:

Sound pressure level (Uncertainty K=3dB(A)) .......................

Sound power level (Uncertainty K=3dB(A)) ............................

Wear ear protectors!

Total vibration values (vector sum in the three axes) 

determined according to EN 62841.

Vibration emission value a

h 

  Impact tightening of fasteners of the maximum capacity of the tool .

  Uncertainty K= .....................................................................

 WARNING Read all safety warnings, instructions, 

illustrations and specifi cations provided with this power 

tool. 

Failure to follow all instructions listed below may result 

in electric shock, fi re and/or serious injury.

Save all warnings and instructions for future reference.

IMPACT DRIVER SAFETY WARNINGS

Hold the power tool by insulated gripping surfaces, 

when performing an operation where the fastener may 

contact hidden wiring. 

Fasteners contacting a "live“ wire 

may make exposed metal parts of the power tool "live“ and 

could give the operator an electric shock.

Wear ear protectors.

 Exposure to noise can cause hearing 

loss.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Use protective equipment. Always wear safety glasses when 

working with the machine. The use of protective clothing is 

recommended, such as dust mask, protective gloves, sturdy 

non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to 

health. Do not inhale the dust. Wear a suitable dust 

protection mask.
Do not machine any materials that present a danger to 

health (e.g. asbestos).
Switch the device off  immediately if the insertion tool stalls! 

Do not switch the device on again while the insertion tool is 

stalled, as doing so could trigger a sudden recoil with a high 

reactive force. Determine why the insertion tool stalled and 

rectify this, paying heed to the safety instructions.
The possible causes may be:
•  it is tilted in the workpiece to be machined
•  it has pierced through the material to be machined
•  the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.

WARNING! 

Danger of burns

•  when changing tools
•  when setting the device down
Chips and splinters must not be removed while the machine 

is running.
When working in walls ceiling, or fl oor, take care to avoid 

electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped 

workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the 

machine.
Do not dispose of used battery packs in the household 

refuse or by burning them. AEG Distributors off er to retrieve 

old batteries to protect our environment.
Do not store the battery pack together with metal objects 

(short circuit risk).
Use only AL1214G3 chargers for charging System L1215G3 

and L1220G3 battery packs. Do not use battery packs from 

other systems.

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given 

in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent 

applications, with diff erent accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase 

the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off  or 

when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the 

accessories, keep the hands warm, organisation of work patterns.

470 175 - BSS12G3.indd   12

470 175 - BSS12G3.indd   12

29.04.2019   09:10:10

29.04.2019   09:10:10