AEG BS18G4-202C 4935478630 - Инструкция по эксплуатации - Страница 18

18

 BS18G4

4811 65 01 XXXXXX MJJJJ

18 V 

500 min

-1

1800 min

-1

13 mm

54 mm

6 mm

60 Nm

2 - 13 mm

1,3 kg

1,7 kg

-18...+50 °C

L1840R, L1830R, L1820R, L1815R

BL1218

81,5 dB(A) / 5 dB(A)

92,5 dB(A) / 5 dB(A)

1,6 m/s

2

 / 1,5m/s

2

ENGLISH

TECHNICAL DATA 

Type 
Production code 
Battery voltage
No-load speed 1st gear 
No-load speed 2nd gear 
Drilling capacity in steel 
Drilling capacity in wood 
Wood screws (without pre-drilling) 
Torque max 
Drill chuck range 
Weight without battery 
Weight according EPTA-Procedure 01/2014 (L1820S) 
Recommended ambient operating temperature 
Recommended battery types 
Recommended charger 

Noise Information: 

Measured values determined according to EN 62841.

Typically, the A-weighted noise levels of the tool are:

Sound pressure level / Uncertainty K 

Sound power level / Uncertainty K

Wear ear protectors!
Vibration Information: 

Total vibration values (vector sum in the three axes) determined 

according to EN 62841.

Vibration emission value a

h  

/ Uncertainty K

  Drilling into metal 

WARNING

  Read all safety warnings, instructions, 

illustrations and specifications provided with this power 

tool.

 Failure to follow all instructions listed below may result in 

electric shock, fire and/or serious injury. 

Save all warnings and instructions for future reference.

DRILL SAFETY WARNINGS

Safety instructions for all operations

Hold the power tool by insulated gripping surfaces, when 

performing an operation where the cutting accessory or 

fasteners may contact hidden wiring.

Cutting accessory or fasteners contacting a “live” wire may make 

exposed metal parts of the power tool “live” and could give the 

operator an electric shock.

Safety instructions when using long drill bits
Never operate at higher speed than the maximum speed 

rated of the drill bit.

 At higher speeds, the bit is likely to bend 

if allowed to rotate freely without contacting the workpiece, 

resulting the personal injury.

Always start drilling at low speed and with the bit tip in 

contact with the workpiece. 

At higher speeds, the bit is likely to 

bend if allowed to rotate freely without contacting the workpiece, 

resulting the personal injury.

Apply pressure only in direct line with the bit and do not 

apply excessive pressure. 

Bits can bend causing breakage or 

loss of control, resulting in personal injury.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Use protective equipment. Always wear safety glasses when 

working with the machine. The use of protective clothing is 

recommended, such as dust mask, protective gloves, sturdy 

non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to 

health. Do not inhale the dust. Wear a suitable dust protection 

mask.
Do not machine any materials that present a danger to health 

(e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do 

not switch the device on again while the insertion tool is stalled, 

as doing so could trigger a sudden recoil with a high reactive 

force. Determine why the insertion tool stalled and rectify this, 

paying heed to the safety instructions.
The possible causes may be:

WARNING

The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test 

given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different 

applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly 

increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or 

when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the 

accessories, keep the hands warm, organization of work patterns.

Cordless Drill Driver

470 486 - BS18G4.indd   18

470 486 - BS18G4.indd   18

22.01.2021   12:51:08

22.01.2021   12:51:08