Skil 9176 - Инструкция по эксплуатации - Страница 6

6

d) 

Store idle power tools out of the reach of children 

and do not allow persons unfamiliar with the power 

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained 

users.

e) 

Maintain power tools. Check for misalignment or 

binding of moving parts, breakage of parts and any 

other condition that may affect the power tool’s 

operation. If damaged, have the power tool repaired 

before use.

 Many accidents are caused by poorly 

maintained power tools.

f) 

Keep cutting tools sharp and clean.

 Properly 

maintained cutting tools with sharp cutting edges are less 

likely to bind and are easier to control.

g) 

Use the power tool, accessories and tool bits etc., in 

accordance with these instructions, taking into 

account the working conditions and the work to be 

performed.

 Use of the power tool for operations different 

from those intended could result in a hazardous situation.

5) SERVICE

a) 

Have your power tool serviced by a qualified repair 

person using only identical replacement parts.

 This 

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR ANGLE GRINDERS

1) SAFETY INSTRUCTIONS FOR ALL OPERATIONS

a) 

This power tool is intended to function as a grinder, 

sander, wire brush or cut-off tool. Read all safety 

warnings, instructions, illustrations and 

specifications provided with this power tool. 

Failure 

to follow all instructions listed below may result in electric 

shock, fire and/or serious injury.

b) 

This power tool is not recommended for polishing.

Operations for which the power tool was not designed 

may create a hazard and cause personal injury.

c) 

Do not use accessories which are not specifically 

designed and recommended by the tool 

manufacturer. 

Just because the accessory can be 

attached to your power tool, it does not assure safe 

operation.

d) 

The rated speed of the accessory must be at least 

equal to the maximum speed marked on the power 

tool. 

Accessories running faster than their rated speed 

can fly apart.

e) 

The outside diameter and the thickness of your 

accessory must be within the capacity rating of your 

power tool. 

Incorrectly sized accessories cannot be 

adequately guarded or controlled.

f) 

Threaded mounting of accessories must match the 

grinder spindle thread. For accessories mounted by 

flanges, the arbour hole of the accessory must fit 

the locating diameter of the flange.

 Accessories that 

do not match the mounting hardware of the power tool 

will run out of balance, vibrate excessively and may 

cause loss of control.

g) 

Do not use a damaged accessory. Before each use 

inspect the accessory such as abrasive wheels for 

chips and cracks, backing pads for cracks, tear or 

excess wear, wire brushes for loose or cracked 

wires. If the power tool or accessory is dropped, 

inspect for damage or install an undamaged 

accessory. After inspecting and installing an 

accessory, position yourself and bystanders away 

from the plane of the rotating accessory and run the 

power tool at maximum no load speed for one 

minute. 

Damaged accessories will normally break apart 

during this test time.

h) 

Wear personal protective equipment

4

. 

Depending 

on application, use face shield, safety goggles or 

safety glasses. As appropriate, wear dust mask, 

hearing protectors, gloves and shop apron capable 

of stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping flying 

debris generated by various operations. The dust mask or 

respirator must be capable of filtrating particles 

generated by your operation. Prolonged exposure to high 

intensity noise may cause hearing loss.

i) 

Keep bystanders a safe distance away from work 

area. Anyone entering the work area must wear 

personal protective equipment. 

Fragments of the 

workpiece or of a broken accessory may fly away and 

cause injury beyond the immediate area of operation.

j) 

Hold power tool by insulated gripping surfaces only, 

when performing an operation where the cutting 

accessory may contact hidden wiring or its own 

cord.

 A cutting accessory contacting a “live” wire may 

make exposed metal parts of the power tool “live” and 

could give the operator an electric shock.

k) 

Position the cord clear of the spinning accessory. 

If 

you lose control, the cord may be cut or snagged and 

your hand or arm may be pulled into the spinning 

accessory.

l) 

Never lay the power tool down until the accessory 

has come to a complete stop. 

The spinning accessory 

may grab the surface and pull the power tool out of your 

control.

m) 

Do not run the power tool while carrying it at your 

side. 

Accidental contact with the spinning accessory 

could snag your clothing, pulling the accessory into your 

body.

n) 

Regularly clean the power tool’s air vents. 

The 

motor’s fan will draw the dust inside the housing and 

excessive accumulation of powdered metal may cause 

electrical hazards.

o) 

Do not operate the power tool near flammable 

materials. 

Sparks could ignite these materials.

p) 

Do not use accessories that require liquid coolants. 

Using water or other liquid coolants may result in 

electrocution or shock.

2) KICKBACK AND RELATED WARNINGS

•  Kickback is a sudden reaction to a pinched or snagged 

rotating wheel, backing pad, brush or any other accessory. 

Pinching or snagging causes rapid stalling of the rotating 

accessory which in turn causes the uncontrolled power 

tool to be forced in the direction opposite of the 

accessory’s rotation at the point of the binding.

•  For example, if an abrasive wheel is snagged or pinched 

by the workpiece, the edge of the wheel that is entering 

into the pinch point can dig into the surface of the 

material causing the wheel to climb out or kick out. The 

wheel may either jump toward or away from the operator, 

depending on the direction of the wheel’s movement at 

the point of pinching. Abrasive wheels may also break 

under these conditions.