Skil 7208AG - Инструкция по эксплуатации - Страница 10

10

•  Holding and guiding the tool 

0

!  while working, always hold the tool at the 

grey-coloured grip area(s)

-  guide the tool parallel to the working surface

!  do not apply too much pressure on the tool; let 

the sanding surface do the work for you

-  do not tilt the tool in order to avoid unwanted sanding 

marks

-  keep ventilation slots H 

2

 uncovered

APPLICATION ADVICE

•  Use the tool with its standard foot plate for large working 

surfaces, corners and edges 

!

•  Use the tool with the special sanding attachments for 

hard-to-reach places 

@

•  The flexible sanding attachment is intended for

-  rounding edged surfaces 

#

a

-  all rounded surfaces with a maximum diameter of 

10 cm 

#

b

•  When the delta-tip is worn or damaged at the top, you 

may extend its service life twice by removing it, turning it 

120° and putting it back (also applicable to delta sanding 

sheet) 

$

•  Never use the same sanding sheet for wood and metal

•  Recommended sanding belt grits:

coarse 

-  for removing paint; for sanding of 

extremely rough wood

medium 

-  for sanding of rough or plain wood

fine 

-  for smoothing of wood; for finishing of 

bare wood; for smoothing surfaces with 

old paint

•  Use different grit sizes when the working surface is 

rough:

-  start sanding with coarse or medium grit

-  finish with fine grit

•  For more tips see www.skileurope.com

MAINTENANCE / SERVICE

•  This tool is not intended for professional use

•  Always keep tool and cord clean (especially ventilation 

slots H 

2

)

-  remove adhering sanding dust with a brush

!  disconnect the plug before cleaning

•  If the tool should fail despite the care taken in 

manufacturing and testing procedures, repair should be 

carried out by an after-sales service centre for SKIL 

power tools

-  send the tool 

undismantled

 together with proof of 

purchase to your dealer or the nearest SKIL service 

station (addresses as well as the service diagram of 

the tool are listed on www.skileurope.com)

ENVIRONMENT

• 

Do not dispose of electric tools, accessories and 

packaging together with household waste material

(only for EU countries)

-  in observance of European Directive 2002/96/EC on 

waste of electric and electronic equipment and its 

implementation in accordance with national law, 

electric tools that have reached the end of their life 

must be collected separately and returned to an 

environmentally compatible recycling facility

-  symbol 

%

 will remind you of this when the need for 

disposing occurs

 DECLARATION OF CONFORMITY

•  We declare under our sole responsibility that this product 

is in conformity with the following standards or 

standardized documents: EN 60745, EN 61000, 

EN 55014, in accordance with the provisions of the 

directives 2006/95/EC, 2004/108/EC, 2006/42/EC

• 

Technical file at

: SKIL Europe BV (PT-SEU/PJE), 

4825 BD Breda, NL

ÊÆÇιƼ½ÊÄÇÇÌ

Á»½Ê½ËÁ¼½ÆÌ

ȽʹÌÁÇÆËŵÆ¿Áƽ½ÊÁÆ¿

ÍÊÇȽƓˁ˅ʿ˂ ʽ¼¹Ɠ

¹ÆÊÇÅŽĽÆ

ÈÈÊÇιĹƹ¿½Ê

03.05.2011

NOISE/VIBRATION

•  Measured in accordance with EN 60745 the sound 

pressure level of this tool is 71 dB(A) and the sound 

power level 82 dB(A) (standard deviation: 3 dB), and the 

vibration 14.3 m/s² (hand-arm method; uncertainty 

K = 1.5 m/s²)

•  The vibration emission level has been measured in 

accordance with a standardised test given in EN 60745; it 

may be used to compare one tool with another and as a 

preliminary assessment of exposure to vibration when 

using the tool for the applications mentioned

-  using the tool for different applications, or with different 

or poorly maintainted accessories, may significantly 

increase

 the exposure level

-  the times when the tool is switched off or when it is 

running but not actually doing the job, may significantly 

reduce

 the exposure level

!  protect yourself against the effects of vibration 

by maintaining the tool and its accessories, 

keeping your hands warm, and organizing your 

work patterns

Ponceuse polyvalente 

7207/7208

INTRODUCTION

•  Cet outil sert au ponçage et au polissage à sec du bois, 

des surfaces peintes, du plastique et du mastic

•  Cet outil n’est conçu pour un usage professionnel

•  Lisez et conservez ce manuel d’instruction 

3

SPECIFICATIONS TECHNIQUES 

1