Ryobi RSS280-S - Инструкция по эксплуатации - Страница 4

2

| English

 WARNING

Injuries may be caused or aggravated by prolonged use 
of a tool. When using any tool for prolonged periods, 
ensure you take regular breaks.

KNOW YOUR PRODUCT

See page 93.

1. On/off switch
2.  Variable speed control selector
3.  1/3 Sheet pad
4. Paper Clamp
5.  Dust collection box
6.  Handle, insulated gripping surface
7. Adhesive sandpaper
8. Non-adhesive sandpaper

SANDPAPER SELECTION

Selecting the correct size, grit and type of sand paper is an 
extremely important step in achieving a high quality sanded 

fi

 nish. Aluminum oxide, silicon carbide, and other synthetic 

abrasives are best for power sanding. Natural abrasives, 
such as 

fl

 int and garnet are too soft for economical use in 

power sanding.
In general, coarse grit will remove the most material 
and 

fi

 ner grit will produce the best 

fi

 nish in all sanding 

operations. The condition of the surface to be sanded will 
determine which grit will do the job. If the surface is rough, 
start with a coarse grit and sand until the surface is uniform. 
Medium grit may then be used to remove scratches left 
by the coarser grit and 

fi

 ner grit used for 

fi

 nishing of the 

surface. Always continue sanding with each grit until 
surface is uniform.

 WARNING

Do not use sander without sandpaper; doing so will 
damage the cushion.

Sheet/pad recommended use

80-grit sanding sheet 

Coarse sanding

120-grit sanding sheet

Light sanding

150-grit sanding sheet

Light sanding

MAINTENANCE

 WARNING

The product should never be connected to a power 
supply when assembling parts, making adjustments, 
cleaning, performing maintenance, or when the product 
is not in use. Disconnecting the product from the power 
supply will prevent accidental starting that could cause 
serious injury.

■

When servicing, use only identical RYOBI replacement 
parts. Use of any other parts may create a hazard or 
cause product damage.

■

Avoid using solvents when cleaning plastic parts. Most 
plastics are susceptible to various types of commercial 
solvents and may be damaged by their use. Use clean 
cloths to remove dirt, carbon dust, etc.

■

Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact 
with plastic parts. They contain chemicals that can 
damage, weaken or destroy plastic.

■

Always wear safety goggles or safety glasses with side 
shields during power tool operation or when blowing 
dust. If operation is dusty, also wear a dust mask.

■

If the power supply cord is damaged, it must be 
replaced only by the manufacturer or by an authorized 
service center to avoid risk. Contact authorized service 
center.

■

For greater safety and reliability, all repairs should be 
performed by an Authorised RYOBI Service Centre.

 WARNING

Electrical tools used on 

fi

 berglass material, wallboard, 

spackling compounds, or plaster are subject to 
accelerated wear and possible premature failure 
because the 

fi

 berglass chips and grindings are highly 

abrasive to bearings, brushes, commutators, etc. We do 
not recommend using the product for extended work on 
these types of materials.

 WARNING

Do not use compressed air to blow dust from the product. 
This practice is dangerous and can cause dirt and grit to 
be blasted into someone’s eyes, causing injury.

LUBRICATION

All of the bearings in the product are lubricated with a 
suf

fi

 cient amount of high grade lubricant for the life span of 

the product under normal operating conditions. Therefore, 
no further lubrication is required.

CLEANING THE SANDING SHEETS

The sanding sheets that come with the product are made to 
be re-used. Therefore, it is important that they be cleaned 
periodically to remove sanding residue and foreign material 
that can accumulate over time. 
To clean sanding sheets, rub the sheets with a hard rubber 
block. You can also use the clean rubber sole of a shoe.

ENVIRONMENTAL PROTECTION 

Recycle raw materials instead of disposing 
of as waste. The machine, accessories and 
packaging should be sorted for environment-
friendly recycling.

SYMBOL

Safety Alert