Ryobi EBS750 - Инструкция по эксплуатации - Страница 3

English

1

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

EL

TR

 WARNING

Read all safety warnings and all instructions.

 Failure 

to follow the warnings and instructions may result in 

electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference

.

SANDER SAFETY WARNINGS

■

Hold power tool by insulated gripping surfaces, 

because the belt may contact its own cord.

 Cutting a 

“live” wire may make exposed metal parts of the power 

tool “live” and could give the operator an electric shock.

■

Always wear safety goggles and a dust mask when 

sanding, especially sanding overhead.

■

A suitable breathing respirator must be worn while 

sanding lead paint, some woods and metal to avoid 

breathing the harmful/toxic dust or air.

■

The machine is not suitable for wet sanding.

■

Do not use sanding belt larger than needed.

 WARNING

Do not throw sanding dust on an open fire

 because 

materials in fine particle form may be explosive.

 WARNING

If the replacement of the supply cord is necessary, this 

has to be done by the manufacturer or his agent in order 

to avoid a safety hazard

.

INTENDED USE

You may use this product for the purposes listed below:

■

Sanding on wood surfaces.

■

Removing rust from and sanding steel surfaces.

MAINTENANCE

 WARNING

The tool should never be connected to a power supply 

when  you  are  assembling  parts,  making  adjustments, 

cleaning, performing maintenance, or when the tool is 

not in use. Disconnecting the tool will prevent accidental 

starting that could cause serious injury.

 WARNING

When servicing use only identical Ryobi replacement 

parts.  Use  of  any  other  parts  may  create  a  hazard  or 

cause product damage.

GENERAL

Avoid  using  solvents  when  cleaning  plastic  parts.  Most 

plastics are susceptible to various types of commercial 

solvents  and  may  be  damaged  by  their  use.  Use  clean 

cloths to remove dirt, carbon dust, etc.

 WARNING

Do not at any time let brake fluids, gasoline, petroleum-

based  products,  penetrating  oils,  etc.  come  in  contact 

with  plastic  parts.  They  contain  chemicals  that  can 

damage, weaken or destroy plastic.

Electric  tools  used  on  fiberglass  material,  wallboard, 

spackling compounds, or plaster are subject to accelerated 

wear and possible premature failure because the fiberglass 

chips and grindings are highly abrasive to bearings, 

brushes,  commutators,  etc.  Consequently,  we  do  not 

recommend using this tool for extended work on these 

types  of  materials.  However,  if  you  do  work  with  any  of 

these materials, it is extremely important to clean the tool 

using compressed air.

 WARNING

Always wear safety goggles or safety glasses with side 

shields during power tool operation or when blowing 

dust. If operation is dusty, also wear a dust mask.

LUBRICATION

All of the bearings in this tool are lubricated with a sufficient 

amount of high grade lubricant for the life of the unit 

under  normal  operating  conditions.  Therefore,  no  further 

lubrication is required.

CLEANING THE SANDING BELT

The sanding belt that came with your sander is made to 

be  re-used.  Therefore,  it  is  important  that  it  be  cleaned 

periodically to remove sanding residue and foreign material 

that  can  accumulate  over  time.  One  of  the  ways  to  clean 

sanding belt is to rub the sheets with a hard rubber block. 

You can also use the clean rubber sole of a shoe.

 WARNING

Always remove the sanding belt from sander before 

cleaning. Failure to do so could cause serious personal 

injury.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing 

of as waste. The machine, accessories 

and packaging should be sorted for 

environmental-friendly recycling.