Metabo SXE 150-5.0 BL - Инструкция по эксплуатации - Страница 10

ENGLISH

en

10

• The electronic signal indicator (3) does not 

light up when the machine is switched on:

The mains cable (7) is not connected properly to the 

machine or mains socket. 
Connect the machine properly.

• Overload protection: The electronic signal 

indicator (3) lights red and the speed of the 

machine drops to 4000 min

-1 

(rpm) during 

the grinding process:

The temperature in the machine is too high. The 

pressure on the machine is too high for a longer 

time.
Exert less pressure on the machine for a moment, 

then the speed of the machine will increase again.

• Overload protection: The electronic signal 

indicator (3) lights red and the speed of the 

machine decreases slightly:

The pressure on the machine is too high for a short 

time.
Exert less pressure on the machine, then the LED 

indicator (3) automatically switches back to green.

• Electronic safety shutdown: The electronic 

signal indicator (3) lights red and the 

machine has stopped:

The machine is in safety mode due to the high 

temperature.
Wait until the machine has cooled down and the 

electronic signal indicator goes off.

• The support plate brake does not work:

Work braking ring (13) or damaged spindle bearing. 
Check the braking ring (13) and replace if required 

(see chapter 8.). If the spindle bearing is defective, 

have it replaced (see chapter 11.).

Use only genuine Metabo accessories.
Note: Metabo accessories are adapted to suit the 

machine's hook and loop-type fastening. This 

increases the service life of the hook and loop-type 

fastening.
Use only accessories which fulfil the requirements 

and specifications listed in these operating 

instructions.
See www.metabo.com or the catalogue for a 

complete range of accessories.

Repairs to electrical tools must only be carried 

out by qualified electricians! 

Contact your local Metabo representative if you 

have Metabo power tools requiring repairs. See 

www.metabo.com for addresses.
You can download a list of spare parts from 

www.metabo.com.

Observe national regulations on environmentally 

compatible disposal and on the recycling of disused 

machines, packaging and accessories.

Only for EU countries: never dispose of 

power tools in your household waste! Used 

power tools must be collected separately and 

handed in for environmentally compatible recycling 

in accordance with European Directive 2012/19/EU 

on waste electrical and electronic equipment and its 

implementation in national legal systems.

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
D

= Diameter of support plate

P

1

= Rated  input  power

n

0

= Idle  speed

n

1

= Speed at rated load

S

= Oscillating circuit diameter

m

= Weight without mains cable

Measured values determined in conformity with 

EN 60745.

~ 

AC Power

Machine in protection class I
The technical specifications quoted are subject to 

tolerances (in compliance with the relevant valid 

standards).

Emission values

These values make it possible to assess the 

emissions from the power tool and to compare 

different power tools. The actual load may be higher 

or lower depending on the operating conditions, the 

condition of the power tool or the accessories. 

Please allow for breaks and periods when the load 

is lower for assessment purposes. Arrange 

protective measures for the user e.g. organisational 

measures based on the adjusted estimates. 
Vibration total value (vector sum of three directions) 

determined in accordance with EN 60745:

a

h, DS

= Vibration emission value (surface 

grinding)

K

h,DS

= Uncertainty (vibration)

Typical A-effective perceived sound levels:

L

pA

= Sound-pressure level

L

WA

= Acoustic power level

K

pA

, K

WA

=Uncertainty

The noise level can exceed 80 dB(A) during 

operation.

Wear ear protectors!

10. Accessories

11. Repairs

12. Environmental Protection

13. Technical Specifications