Makita M9508 - Инструкция по эксплуатации - Страница 6

6 ENGLISH

Kickback is the result of power tool misuse and/or 

incorrect operating procedures or conditions and can be 

avoided by taking proper precautions as given below.

1. 

Maintain a firm grip on the power tool and 

position your body and arm to allow you to 

resist kickback forces. Always use auxiliary 

handle, if provided, for maximum control over 

kickback or torque reaction during start-up.

The operator can control torque reactions or kick

-

back forces, if proper precautions are taken.

2. 

Never place your hand near the rotating acces-

sory.

 Accessory may kickback over your hand.

3. 

Do not position your body in the area where 

power tool will move if kickback occurs.

Kickback will propel the tool in direction opposite 

to the wheel’s movement at the point of snagging.

4. 

Use special care when working corners, sharp 

edges etc. Avoid bouncing and snagging the 

accessory.

 Corners, sharp edges or bouncing 

have a tendency to snag the rotating accessory 

and cause loss of control or kickback.

5. 

Do not attach a saw chain woodcarving blade 

or toothed saw blade.

 Such blades create fre

-

quent kickback and loss of control.

Safety Warnings Specific for Grinding Operation:

1. 

Use only wheel types that are recommended 

for your power tool and the specific guard 

designed for the selected wheel.

 Wheels for 

which the power tool was not designed cannot be 

adequately guarded and are unsafe.

2. 

The grinding surface of centre depressed 

wheels must be mounted below the plane of 

the guard lip.

 An improperly mounted wheel that 

projects through the plane of the guard lip cannot 

be adequately protected.

3. 

The guard must be securely attached to the 

power tool and positioned for maximum safety, 

so the least amount of wheel is exposed 

towards the operator. 

The guard helps to protect 

the operator from broken wheel fragments, acci

-

dental contact with wheel and sparks that could 

ignite clothing.

4. 

Wheels must be used only for recommended 

applications. For example: do not grind with 

the side of cut-off wheel.

 Abrasive cut-off wheels 

are intended for peripheral grinding, side forces 

applied to these wheels may cause them to 

shatter.

5. 

Always use undamaged wheel flanges that are 

of correct size and shape for your selected 

wheel.

 Proper wheel flanges support the wheel 

thus reducing the possibility of wheel breakage. 

Flanges for cut-off wheels may be different from 

grinding wheel flanges.

6. 

Do not use worn down wheels from larger 

power tools.

 Wheel intended for larger power tool 

is not suitable for the higher speed of a smaller 

tool and may burst.

Additional Safety Warnings:

1. 

When using depressed centre grinding wheels, 

be sure to use only fiberglass-reinforced 

wheels.

2. 

NEVER USE Stone Cup type wheels with this 

grinder.

 This grinder is not designed for these 

types of wheels and the use of such a product 

may result in serious personal injury.

3. 

Be careful not to damage the spindle, the 

flange (especially the installing surface) or the 

lock nut. Damage to these parts could result in 

wheel breakage.

4. 

Make sure the wheel is not contacting the 

workpiece before the switch is turned on.

5. 

Before using the tool on an actual workpiece, 

let it run for a while. Watch for vibration or 

wobbling that could indicate poor installation 

or a poorly balanced wheel.

6. 

Use the specified surface of the wheel to per

-

form the grinding.

7. 

Do not leave the tool running. Operate the tool 

only when hand-held.

8. 

Do not touch the workpiece immediately after 

operation; it may be extremely hot and could 

burn your skin.

9. 

Observe the instructions of the manufacturer 

for correct mounting and use of wheels. 

Handle and store wheels with care.

10. 

Do not use separate reducing bushings or 

adaptors to adapt large hole abrasive wheels.

11. 

Use only flanges specified for this tool.

12. 

For tools intended to be fitted with threaded 

hole wheel, ensure that the thread in the wheel 

is long enough to accept the spindle length.

13. 

Check that the workpiece is properly 

supported.

14. 

Pay attention that the wheel continues to 

rotate after the tool is switched off.

15. 

If working place is extremely hot and humid, 

or badly polluted by conductive dust, use a 

short-circuit breaker (30 mA) to assure opera-

tor safety.

16. 

Do not use the tool on any materials contain-

ing asbestos.

17. 

Do not use cloth work gloves during operation.

Fibers from cloth gloves may enter the tool, which 

causes tool breakage.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity 

with product (gained from repeated use) replace 

strict adherence to safety rules for the subject 

product. MISUSE or failure to follow the safety 

rules stated in this instruction manual may cause 

serious personal injury.