Makita M9507 - Инструкция по эксплуатации - Страница 5

5 ENGLISH

5. 

Maintain power tools. Check for misalignment 

or binding of moving parts, breakage of parts 

and any other condition that may affect the 

power tool’s operation. If damaged, have the 

power tool repaired before use.

 Many accidents 

are caused by poorly maintained power tools.

6. 

Keep cutting tools sharp and clean.

 Properly 

maintained cutting tools with sharp cutting edges 

are less likely to bind and are easier to control.

7. 

Use the power tool, accessories and tool bits 

etc. in accordance with these instructions, tak-

ing into account the working conditions and 

the work to be performed.

 Use of the power tool 

for operations different from those intended could 

result in a hazardous situation.

Service

1. 

Have your power tool serviced by a qualified 

repair person using only identical replacement 

parts.

 This will ensure that the safety of the power 

tool is maintained.

2. 

Follow instruction for lubricating and chang-

ing accessories.

3. 

Keep handles dry, clean and free from oil and 

grease.

Grinder safety warnings

Safety Warnings Common for Grinding Operations:

1. 

This power tool is intended to function as a 

grinder. Read all safety warnings, instructions, 

illustrations and specifications provided with 

this power tool.

 Failure to follow all instructions 

listed below may result in electric shock, fire and/

or serious injury.

2. 

Operations such as sanding, wire brushing, 

polishing or cutting-off are not recommended 

to be performed with this power tool.

 Operations 

for which the power tool was not designed may 

create a hazard and cause personal injury.

3. 

Do not use accessories which are not specifi

-

cally designed and recommended by the tool 

manufacturer.

 Just because the accessory can 

be attached to your power tool, it does not assure 

safe operation.

4. 

The rated speed of the accessory must be at 

least equal to the maximum speed marked on 

the power tool.

 Accessories running faster than 

their rated speed can break and fly apart.

5. 

The outside diameter and the thickness of your 

accessory must be within the capacity rating 

of your power tool.

 Incorrectly sized accessories 

cannot be adequately guarded or controlled.

6. 

Threaded mounting of accessories must match 

the grinder spindle thread. For accessories 

mounted by flanges, the arbour hole of the 

accessory must fit the locating diameter of the 

flange.

 Accessories that do not match the mounting 

hardware of the power tool will run out of balance, 

vibrate excessively and may cause loss of control.

7. 

Do not use a damaged accessory. Before each 

use inspect the accessory such as abrasive 

wheels for chips and cracks, backing pad for 

cracks, tear or excess wear. If power tool or 

accessory is dropped, inspect for damage or 

install an undamaged accessory. After inspecting 

and installing an accessory, position yourself and 

bystanders away from the plane of the rotating 

accessory and run the power tool at maximum 

no-load speed for one minute.

 Damaged accesso-

ries will normally break apart during this test time.

8. 

Wear personal protective equipment. 

Depending on application, use face shield, 

safety goggles or safety glasses. As appropri-

ate, wear dust mask, hearing protectors, gloves 

and workshop apron capable of stopping small 

abrasive or workpiece fragments.

 The eye pro-

tection must be capable of stopping flying debris 

generated by various operations. The dust mask 

or respirator must be capable of filtrating particles 

generated by your operation. Prolonged exposure 

to high intensity noise may cause hearing loss.

9. 

Keep bystanders a safe distance away from 

work area. Anyone entering the work area 

must wear personal protective equipment.

Fragments of workpiece or of a broken accessory 

may fly away and cause injury beyond immediate 

area of operation.

10. 

Hold the power tool by insulated gripping 

surfaces only, when performing an operation 

where the cutting accessory may contact hid-

den wiring or its own cord.

 Cutting accessory 

contacting a "live" wire may make exposed metal 

parts of the power tool “live” and could give the 

operator an electric shock.

11. 

Position the cord clear of the spinning acces-

sory.

 If you lose control, the cord may be cut or 

snagged and your hand or arm may be pulled into 

the spinning accessory.

12. 

Never lay the power tool down until the acces-

sory has come to a complete stop.

 The spinning 

accessory may grab the surface and pull the 

power tool out of your control.

13. 

Do not run the power tool while carrying it at 

your side.

 Accidental contact with the spinning 

accessory could snag your clothing, pulling the 

accessory into your body.

14. 

Regularly clean the power tool’s air vents.

 The 

motor’s fan will draw the dust inside the housing 

and excessive accumulation of powdered metal 

may cause electrical hazards.

15. 

Do not operate the power tool near flammable 

materials.

 Sparks could ignite these materials.

16. 

Do not use accessories that require liquid 

coolants.

 Using water or other liquid coolants 

may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged 

rotating wheel, backing pad, brush or any other acces

-

sory. Pinching or snagging causes rapid stalling of the 

rotating accessory which in turn causes the uncon-

trolled power tool to be forced in the direction opposite 

of the accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or 

pinched by the workpiece, the edge of the wheel that is 

entering into the pinch point can dig into the surface of 

the material causing the wheel to climb out or kick out. 

The wheel may either jump toward or away from the 

operator, depending on direction of the wheel’s move-

ment at the point of pinching. Abrasive wheels may also 

break under these conditions.