Bosch GWS 7 115 - Инструкция по эксплуатации - Страница 14

14

 | English 

1 609 92A 0EE | (13.8.13)

Bosch Power Tools



Release the On/Off switch and set it to the off position 
when the power supply is interrupted, e. g., in case of a 
power failure or when the mains plug is pulled. 

This pre-

vents uncontrolled restarting.



Dusts from materials such as lead-containing coatings, 
some wood types, minerals and metal can be harmful to 
one’s health and cause allergic reactions, lead to res-
piratory infections and/or cancer.

 Materials containing 

asbestos may only be worked by specialists.

–

As far as possible, use a dust extraction system suita-
ble for the material.

–

Provide for good ventilation of the working place.

–

It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the 
materials to be worked.



Prevent dust accumulation at the workplace. 

Dusts can 

easily ignite.



Secure the workpiece. 

A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.



After breakage of the grinding disc during operation or 
damage to the holding fixtures on the protection 
guard/power tool, the machine must promptly be sent to 
an after-sales service agent for maintenance for address-
es, see section “After-sales Service and Application Ser-
vice”.



Adjust protection guard in such a manner that sparking 
toward the operator is prevented.



Do not touch grinding and cutting discs before they 
have cooled down. 

The discs can become very hot while 

working.



Actuate the spindle lock button only when the grinder 
spindle is at a standstill. 

Otherwise, the machine may be-

come damaged.



After mounting the grinding tool and before switching 
on, check that the grinding tool is correctly mounted 
and that it can turn freely. Make sure that the grinding 
tool does not graze against the protection guard or oth-
er parts.



When operating the machine with power from mobile gen-
erators, loss of performance or untypical behavior can oc-
cur upon switching on.



By applying too high application force, the machine can 
be subject to overload. Overload can lead to overheat-
ing and damage of the power tool. After heavily strain-
ing the power tool, continue to run it at no-load for sev-
eral minutes in order to cool it down.



Do not use the power tool with a cut-off stand.



Never use a cutting disc for roughing.



The quick-clamping nut may be used only for grinding 
or cutting discs. Use only a flawless, undamaged quick-
clamping nut.



For operations with the rubber sanding plate  or with 
the cup brush/wheel brush/flap disc, always mount the 
hand guard .



For cutting with bonded abrasives, always use a pro-
tection guard for cutting.



Provide for sufficient dust extraction when cutting 
stone. 

Wear a dust respirator.

Products sold in GB only

: Your product is fitted with an 

BS 1363/A approved electric plug with internal fuse (ASTA 
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be 
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should 
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible 
shock hazard and should never be inserted into a mains sock-
et elsewhere.

Products sold in AUS and NZ only

: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

Symbols

The following symbols are important for reading and under-
standing the operating instructions. Please take note of the 
symbols and their meaning. The correct interpretation of the 
symbols will help you to use the machine in a better and safer 
manner.

Symbol

Meaning

Article number

Read all safety warnings and all instruc-
tions

Before any work on the machine itself, 
pull the mains plug from the socket out-
let

Wear protective gloves

Always wear ear protection

Wear safety glasses/goggles

Movement direction

Apply strength for the workstep.

Low speed

OBJ_BUCH-1188-003.book  Page 14  Tuesday, August 13, 2013  2:49 PM