Bosch 0.601.9F2.000 - Инструкция по эксплуатации - Страница 15

 English | 

15

Bosch Power Tools

1 609 92A 29F | (21.7.16)



Maintain a firm grip on the power tool and position your 
body and arm to allow you to resist kickback forces. Al-
ways use auxiliary handle, if provided, for maximum 
control over kickback or torque reaction during 
start-up. 

The operator can control torque reactions or 

kickback forces, if proper precautions are taken.



Never place your hand near the rotating accessory. 

Ac-

cessory may kickback over your hand.



Do not position your body in the area where power tool 
will move if kickback occurs. 

Kickback will propel the 

tool in direction opposite to the wheel’s movement at the 
point of snagging.



Use special care when working corners, sharp edges, 
etc. Avoid bouncing and snagging the accessory. 

Cor-

ners, sharp edges or bouncing have a tendency to snag the 
rotating accessory and cause loss of control or kickback.



Do not attach a saw chain woodcarving blade or 
toothed saw blade. 

Such blades create frequent kickback 

and loss of control.

Safety warnings specific for Grinding and Abrasive 
Cutting-Off operations



Use only wheel types that are recommended for your 
power tool and the specific guard designed for the se-
lected wheel. 

Wheels for which the power tool was not de-

signed cannot be adequately guarded and are unsafe.



The grinding surface of the centre depressed wheels 
must be mounted below the plane of the guard lip. 

An 

improperly mounted wheel that projects through the plane 
of the guard lip cannot be adequately protected.



The guard must be securely attached to the power tool 
and positioned for maximum safety, so the least 
amount of wheel is exposed towards the operator. 

The 

guard helps to protect operator from broken wheel frag-
ments, accidental contact with wheel and sparks that 
could ignite clothing.



Wheels must be used only for recommended applica-
tions. For example: do not grind with the side of the 
cut-off wheel. 

Abrasive cut-off wheels are intended for 

peripheral grinding; side forces applied to these wheels 
may cause them to shatter.



Always use undamaged wheel flanges that are of cor-
rect size and shape for your selected wheel. 

Proper 

wheel flanges support the wheel thus reducing the possi-
bility of wheel breakage. Flanges for cut-off wheels may be 
different from grinding wheel flanges.



Do not use worn down reinforced wheels from larger 
power tools. 

Wheels intended for larger power tools are 

not suitable for the higher speed of a smaller tool and may 
burst.

Additional safety warnings specific for abrasive cutting 
off operations



Do not “jam” the cut-off wheel or apply excessive pres-
sure. Do not attempt to make an excessive depth of cut. 

Overstressing the wheel increases the loading and suscep-
tibility to twisting or binding of the wheel in the cut and the 
possibility of kickback or wheel breakage.



Do not position your body in line with and behind the 
rotating wheel. 

When the wheel, at the point of operation, 

is moving away from your body, the possible kickback may 
propel the spinning wheel and the power tool directly at 
you. 



When wheel is binding or when interrupting a cut for 
any reason, switch off the power tool and hold the pow-
er tool motionless until the wheel comes to a complete 
stop. Never attempt to remove the cut-off wheel from 
the cut while the wheel is in motion otherwise kickback 
may occur. 

Investigate and take corrective action to elimi-

nate the cause of wheel binding.



Do not restart the cutting operation in the workpiece. 
Let the wheel reach full speed and carefully re-enter 
the cut. 

The wheel may bind, walk up or kickback if the 

power tool is restarted in the workpiece.



Support panels or any oversized workpiece to minimize 
the risk of wheel pinching and kickback. 

Large work-

pieces tend to sag under their own weight. Supports must 
be placed under the workpiece near the line of cut and near 
the edge of the workpiece on both sides of the wheel.



Use extra caution when making “plunge cuts” into ex-
isting walls or other blind areas. 

The protruding wheel 

may cut gas or water pipes, electrical wiring or objects that 
can cause kickback.

Additional safety warnings

Wear safety goggles.



Use appropriate detectors to determine if utility lines 
are hidden in the work area or call the local utility com-
pany for assistance. 

Contact with electric lines can lead 

to fire and electric shock. Damaging a gas line can lead to 
explosion. Penetrating a water line causes property dam-
age.



Release the On/Off switch and set it to the off position 
when the power supply is interrupted, e.g. when the 
battery pack is removed.



Do not touch grinding and cutting discs before they 
have cooled down. 

The discs can become very hot while 

working.



Secure the workpiece. 

A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.



Do not open the battery. 

Danger of short-circuiting.

Protect the battery against heat, e. g., against 
continuous intense sunlight, fire, water, and 
moisture. 

Danger of explosion.



In case of damage and improper use of the battery, 
vapours may be emitted. Ventilate the area and seek 
medical help in case of complaints. 

The vapours can 

irritate the respiratory system.



Use the battery only in conjunction with your Bosch 
product. 

This measure alone protects the battery against 

dangerous overload.

OBJ_BUCH-2937-001.book  Page 15  Thursday, July 21, 2016  1:30 PM