Bort BWS-1700-S - Инструкция по эксплуатации - Страница 10

10

cutting tools with sharp cutting edges are less likely to 

bind and are easier to control .

•  Use the power tool, accessories and tool bits etc . in ac-

cordance with these instructions, taking into account the 

working conditions and the work to be performed . Use 

of the power tool for operations different from those in-

tended could result in a hazardous situation .

Service

Have your power tool serviced by a qualified repair person 

using only identical replacement parts . This will ensure that 

the safety of the power tool is maintained .

SAFETY WARNINGS FOR ANGLE GRINDER

•  This power tool is intended to function as a grinder, sand-

er, wire brush or cut-off tool . Read all safety warnings, in-

structions, illustrations and specifications provided with 

this power tool . Failure to follow all instructions listed be-

low may result in electric shock, fire and/or serious injury .

•  Operations such as polishing are not recommended to 

be performed with this power tool . Operations for which 

the power tool was not designed may create a hazard 

and cause personal injury .

•  Do not use accessories which are not specifically de-

signed and recommended by the tool manufacturer . Just 

because the accessory can be attached to your power 

tool, it does not assure safe operation .

•  The rated speed of the accessory must be at least equal 

to the maximum speed marked on the power tool . Ac-

cessories running faster than their rated speed can break 

and fly apart .

•  The outside diameter and the thickness of your acces-

sory must be within the capacity rating of your power 

tool . Incorrectly sized accessories cannot be adequately 

guarded or controlled .

•  Threaded mounting of accessories must match the 

grinder spindle thread . For accessories mounted by 

flanges, the arbour hole of the accessory must fit the 

locating diameter of the flange . Accessories that do not 

match the mounting hardware of the power tool will run 

out of balance, vibrate excessively and may cause loss of 

control .

•  Do not use a damaged accessory . Before each use in-

spect the accessory such as abrasive wheels for chips and 

cracks, backing pad for cracks, tear or excess wear, wire 

brush for loose or cracked wires . If power tool or acces-

sory is dropped, inspect for damage or install an undam-

aged accessory . After inspecting and installing an acces-

sory, position yourself and bystanders away from the 

plane of the rotating accessory and run the power tool at 

maximum no-load speed for one minute . Damaged ac-

cessories will normally break apart during this test time .

•  Wear personal protective equipment . Depending on ap-

plication, use face shield, safety goggles or safety glasses . 

As appropriate, wear dust mask, hearing protectors, 

gloves and shop apron capable of stopping small abra-

sive or workpiece fragments . The eye protection must be 

capable of stopping flying debris generated by various 

operations . The dust mask or respirator must be capable 

of filtrating particles generated by your operation . Pro-

longed exposure to high intensity noise may cause hear-

ing loss .

•  Keep bystanders a safe distance away from work area . 

Anyone entering the work area must wear personal 

protective equipment . Fragments of workpiece or of a 

broken accessory may fly away and cause injury beyond 

immediate area of operation .

•  Hold the power tool by insulated gripping surfaces only, 

when performing an operation where the cutting acces-

sory may contact hidden wiring or its own cord . Cutting 

accessory contacting a “live” wire may make exposed 

metal parts of the power tool “live” and could give the 

operator an electric shock .

•  Position the cord clear of the spinning accessory . If you 

lose control, the cord may be cut or snagged and your 

hand or arm may be pulled into the spinning wheel .

•  Never lay the power tool down until the accessory has 

come to a complete stop . The spinning wheel may grab 

the surface and pull the power tool out of your control .

•  Do not run the power tool while carrying it at your side . 

Accidental contact with the spinning accessory could 

snag your clothing, pulling the accessory into your body .

•  Regularly clean the power tool’s air vents . The motor’s 

fan will draw the dust inside the housing and excessive 

accumulation of powdered metal may cause electrical 

hazards .

•  Do not operate the power tool near flammable materials . 

Sparks could ignite these materials .

•  Do not use accessories that require liquid coolants . Using 

water or other liquid coolants may result in electrocution 

or shock .

Kickback and related warnings

•  Kickback is a sudden reaction to a pinched or snagged ro-

tating wheel, backing pad, brush or any other accessory . 

Pinching or snagging causes rapid stalling of the rotating 

accessory which in turn causes the uncontrolled power 

tool to be forced in the direction opposite of the acces-

sory’s rotation at the point of the binding . For example, 

if an abrasive wheel is snagged or pinched by the work-

piece, the edge of the wheel that is entering into the pinch 

point can dig into the surface of the material causing the 

wheel to climb out or kick out . The wheel may either jump 

toward or away from the operator, depending on direction 

of the wheel’s movement at the point of pinching . Abra-

sive wheels may also break under these conditions . Kick-

back is the result of power tool misuse and/or incorrect 

operating procedures or conditions and can be avoided 

by taking proper precautions as given below .

•  Maintain a firm grip on the power tool and position your 

body and arm to allow you to resist kickback forces . Al-

ways use auxiliary handle, if provided, for maximum con-

trol over kickback or torque reaction during start-up . The 

operator can control torque reactions or kickback forces, 

if proper precautions are taken .

•  Never place your hand near the rotating accessory . Ac-

cessory may kickback over your hand .

•  Do not position your body in the area where power tool 

will move if kickback occurs . Kickback will propel the tool 

in direction opposite to the wheel’s movement at the 

point of snagging .

•  Use special care when working corners, sharp edges, etc . 

Avoid bouncing and snagging the accessory . Corners, 

sharp edges or bouncing have a tendency to snag the