Bort BBS-800-T - Инструкция по эксплуатации - Страница 7

7

turn it on and off . Any power tool that cannot be 

controlled with the switch is dangerous and must 

be repaired .

•  Disconnect the plug from the power source and/

or the battery pack from the power tool before 

making any adjustments, changing accessories, 

or storing power tools . Such preventive safety 

measures reduce the risk of starting the power 

tool accidentally .

•  Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with 

the power tool or these instructions to operate 

the power tool . Power tools are dangerous in the 

hands of untrained users .

•  Maintain power tools . Check for misalignment or 

binding of moving parts, breakage of parts and 

any other condition that may affect the power 

tool’s operation . If damaged, have the power tool 

repaired before use . Many accidents are caused 

by poorly maintained power tools .

•  Keep cutting tools sharp and clean . Properly 

maintained cutting tools with sharp cutting edg-

es are less likely to bind and are easier to control .

•  Use the power tool, accessories and tool bits etc . 

in accordance with these instructions, taking into 

account the working conditions and the work to 

be performed . Use of the power tool for opera-

tions different from those intended could result in 

a hazardous situation .

Service

Have your power tool serviced by a qualified repair 

person using only identical replacement parts . This 

will ensure that the safety of the power tool is main-

tained .

BEFORE USE
Installation of sanding belt

ATTENTION! Always unplug the machine’s power 

cord from the electrical outlet when for a long time 

you do not work with this tool before replacing 

sanding belt as well as before cleaning, setting up 

or repairing tool .

ATTENTION! Before installing a new sanding belt, 

you must clean the sanding pad and rollers from 

dust and dirt .

• Pull the belt tension lever (8) . Be careful, because 

lever in The tensioned position may slip back to the 

closed position . Pull lever until it is locked .

• Take a sanding belt of the required size and grit . 

With using the arrows on the inside of the sanding 

belt, determine the direction of its movement .

• Put on the sanding belt, taking into account the 

direction of its movement on leading and driven 

rollers by holding it from the outside of the bottom 

plate grinding machine .

• Ensure that the sanding belt is centered on the 

bottom plate, and that the arrows correspond to 

the direction of movement of the tape . Let goten-

sion lever .

NOTE: Be careful, because the position of the ten-

sion lever depends from spring tension . Make sure 

that the tension lever is fully lowered .

Adjusting the position of the sanding belt.

• Turn on the sander and let the machine run for 

7-10 seconds . idle .

• Turn the tool over with the grinding belt . Rotating

adjusting screw (6) left or right, adjust tape position

so that its edges protrude at 1-3mm beyond the 

outer edges of both rollers .

ATTENTION! If the sanding belt during tool opera-

tion will being too close to the inside (base of the 

rollers), this may cause wear, torn edges of the tape 

and damage sanding machine .

Installing a dust collector

This machine is equipped with a outlet for dust (5) 

and is completed cartridge dust collector . It is rec-

ommended to use this feature each when working 

with the instrument, as well as wearing a respirator 

and goggles .

Install a dust cartridge on the dust outlet or Con-

nect the nozzle with a special vacuum cleaner .

ATTENTION! It is necessary to regularly clean the 

cartridge dust collector . Be extremely careful when 

removing dust some materials in dusty form can be 

explosive .

Mixtures of dust and oil or water may ignite over 

time . Not overflow the cartridge; remove dust from 

the cartridge when it turns out to be about 2/3 full .

SAFETY WARNINGS FOR SANDER

•  Use the machine only for dry sanding . Penetration 

of water into the machine increases the risk of an 

electric shock .

•  Caution, fire hazard! Avoid overheating the ob-

ject being sanded as well as the sander . Always 

empty the dust collector before taking breaks . In 

unfavourable conditions, e . g ., when sparks emit 

from sanding metals, sanding debris in the dust 

bag, micro filter or paper sack (or in the filter sack 

or filter of the vacuum cleaner) can self-ignite . Par-

ticularly when mixed with remainders of varnish, 

polyurethane or other chemical materials and 

when the sanding debris is hot after long periods 

of working .

•  Secure the workpiece . A workpiece clamped with 

clamping devices or in a vice is held more secure 

than by hand .

•  Keep your workplace clean . Blends of materials 

are particularly dangerous . Dust from light alloys 

can burn or explode .