AEG WS12-125S - Инструкция по эксплуатации - Страница 18

16

GB

English

TECHNICAL DATA 

Angle Grinder

WS 12-125 S 

WS 12-125 SK 

WS 13-125 SXE WS 13-125 SXEK

Noise information 

Measured values determined according to EN 60745. Typically, the A-weighted noise levels of the tool are:

Sound pressure level (Uncertainty K=3dB(A))

89,3 dB (A)

89,3 dB (A)

90,1 dB (A)

90,1 dB (A)

Sound power level (Uncertainty K=3dB(A))

100,3 dB (A)

100,3 dB (A)

101,1 dB (A)

101,1 dB (A)

Wear ear protectors!

Vibration information

Vibration total values (triaxial vector sum) determined according to EN 60745

Surface grinding:  

Vibration emission value a

h,SG

Uncertainty K=

5,8 m/s

2 

1,5 m/s

2

5,8 m/s

2 

1,5 m/s

2

8,0 m/s

2 

1,5 m/s

2

8,0 m/s

2 

1,5 m/s

2

Disk sanding:  

Vibration emission value a

h,DS

Uncertainty K=

5,5 m/s

2 

1,5 m/s

2

5,5 m/s

2 

1,5 m/s

2

7,5 m/s

2 

1,5 m/s

2

7,5 m/s

2 

1,5 m/s

2

For other applications, e.g. Abrasive Cutting-Off Operations or Wire Brushing other vibration values could occur.

WARNING!

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 

and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. 

The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, 

with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over 

the total working period. 

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is 

running but not actually doing the job. This may significantly reduce the exposure level over the total working period. 

Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, 

keep the hands warm, organisation of work patterns.

WARNING! 

Read all safety warnings and all instructions.

 Failure to 

follow the warnings and instructions may result in electric shock, 

fire and/or serious injury. 

Save all warnings and instructions for future reference.

  ANGLE GRINDER SAFET Y WARNINGS

Safety Warnings Common for Grinding, Sanding, Wire 

Brushing or Abrasive Cutting-Off Operations:
a)  This power tool is intended to function as a grinder, 

sander, wire brush or cut-off tool. Read all safety warnings, 

instructions, illustrations and specifications provided with 

this power tool. 

Failure to follow all instructions listed below may 

result in electric shock, fire and/or serious injury.

b)  Operations such as polishing are not recommended 

to be performed with this power tool.

Operations for which 

the power tool was not designed may create a hazard and cause 

personal injury.

c)  Do not use accessories which are not specifically 

designed and recommended by the tool manufacturer.

 Just 

because the accessory can be attached to your power tool, it does 

not assure safe operation.

d)  The rated speed of the accessory must be at least equal 

to the maximum speed marked on the power tool. 

Accesso-

ries running faster than their rated speed can break and fly apart.

e)  The outside diameter and the thickness of your 

accessory must be within the capacity rating of your power 

tool. 

Incorrectly sized accessories cannot be adequately guarded 

or controlled.

f)  Threaded mounting of accessories must match the grin-

der spindle thread. For accessories mounted by flanges, the 

arbour hole of the accessory must fit the locating diameter 

of the flange. 

Accessories that do not match the mounting hard-

ware of the power tool will run out of balance, vibrate excessively 

and may cause loss of control.

g)  Do not use a damaged accessory. Before each use inspect 

the accessory such as abrasive wheels for chips and cracks, 

backing pad for cracks, tear or excess wear, wire brush for 

loose or cracked wires. If power tool or accessory is dropped, 

inspect for damage or install an undamaged accessory. After 

inspecting and installing an accessory, position yourself and 

bystanders away from the plane of the rotating accessory 

and run the power tool at maximum no-load speed for one 

minute. 

Damaged accessories will normally break apart during this 

test time.

h)  Wear personal protective equipment. Depending on 

application, use face shield, safety goggles or safety glasses. 

As appropriate, wear dust mask, hearing protectors, gloves 

and shop apron capable of stopping small abrasive or 

workpiece fragments.

 The eye protection must be capable of 

stopping flying debris generated by various operations. The dust 

mask or respirator must be capable of filtrating particles generated 

by your operation. Prolonged exposure to high intensity noise may 

cause hearing loss.

i)  Keep bystanders a safe distance away from work area. 

Anyone entering the work area must wear personal protec-

tive equipment. 

Fragments of workpiece or of a broken accessory 

may fly away and cause injury beyond immediate area of operation.