AEG FS250 - Инструкция по эксплуатации - Страница 11

8

English

GB

TECHNIC AL DATA 

Oscillating sander

FS250  

Production code

4770 49 01... 

... 000001-999999

Rated input

250 W

Voltage

220-240V AC 

50/60Hz

No-load speed

6000-12000 min 

-1

Orbital travel diameter

2,0 mm

Dimensions of grinding plate

90x187 mm

Weight according EPTA-Procedure 01/2014

1,8 kg

Noise information

Measured values determined according to EN 62841. Typically, the 

A-weighted noise levels of the tool are:

Sound pressure level (Uncertainty K=3dB(A)) 76 dB(A)

Sound power level (Uncertainty K=3dB(A))

87 dB(A)

Wear ear protectors!
Vibration information

Vibration total values (triaxial vector sum) determined according 

to EN 62841
Vibration emission value a

h

Uncertainty K=

5,5 m/s

2

1,5 m/s

2

WARNING!

The vibration and noise emission level given in this information 

sheet has been measured in accordance with a standardized test 

given in EN 62841 and may be used to compare one tool with 

another.It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the 

main applications of the tool. However if the tool is used for diffe-

rent applications, with different accessories or poorly maintained, 

the vibration and noise emission may differ. This may significantly 

increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should 

also take into account the times when the tool is switched off or 

when it is running but not actually doing the job. This may signifi-

cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from 

the effects of vibration and/or noise such as: maintain the tool 

and the accessories, keep the hands warm, organization of work 

patterns.
Wear ear protectors. Exposure to noise can cause hearing loss.

WARNING! 

Read all safety warnings, instructions, illustrations and 

specifications provided with this power tool.

 Failure to follow 

all instructions listed below may result in electric shock, fire and/

or serious injury. 

Save all warnings and instructions for future reference.

 SANDER SAFET Y WARNINGS

Wear ear protectors.

 Exposure to noise can cause hearing loss.

Appliances used at many different locations including wet room 

and open air must be connected via a residual current device (FI, 

RCD, PRCD) of 30mA or less.
Always disconnect the plug from the socket before carrying out any 

work on the machine.
Make sure the machine is switched off before plugging in.
Before use check machine, cable, and plug for any damages or 

material fatigue. Repairs should only be carried out by authorised 

Service Agents.
This machine is suitable only for dry sanding.

ADDITIONAL SAFET Y AND WORKING INSTRUC TIONS

Use protective equipment. Always wear safety glasses when 

working with the machine. The use of protective clothing is recom-

mended, such as dust mask, protective gloves, sturdy non-slip 

footwear, helmet and ear defenders.

Do not reach into the machine while it is running.
Chips and splinters must not be removed while the machine is 

running.
The dust produced when using this tool may be harmful to health. 

Do not inhale the dust.  Use a dust absorption system and wear a 

suitable dust protection mask. Remove deposited dust thoroughly, 

e.g. with a vacuum cleaner.
Do not machine any materials that present a danger to health (e.g. 

asbestos).
When grinding metal, flying sparks are produced. Take care that 

no persons are endangered. Because of the danger of fire, no 

combustible materials should be located in the vicinity (spark flight 

zone). Do not use dust extraction.
Do not let any metal parts enter the airing slots - danger of short 

circuit!

MAINS CONNEC TION

Connect only to single-phase AC system voltage as indicated on 

the rating plate. It is also possible to connect to sockets without an 

earthing contact as the design conforms to safety class II.
Keep mains lead clear from working range of the machine. Always 

lead the cable away behind you.
Before use check machine, cable, and plug for any damages or 

material fatigue. Repairs should only be carried out by authorised 

Service Agents.
Only plug-in when machine is switched off.

SPECIFIED CONDITIONS OF USE

The oscillating sander can be used for sanding wood, plastics and 

metal.

English