Ryobi RRS1200-K - Инструкция по эксплуатации - Страница 4

action, and prolongs blade life.

Ŷ

Never use gasoline since normal sparking of motor 
could ignite fumes.

Ŷ

Clamp the workpiece firmly and cut close to the 
clamping point to eliminate any vibration of the work. 
When cutting conduit pipe or angle iron, secure the 
workpiece with a vise, if possible, and cut close to the 
vise. To cut a thin-sheet material, place the material 
between two hardboards or plywood and clamp the 
layers to eliminate vibration and material tearing.

Ŷ

Always keep firm pressure on the base to hold it 
securely against the workpiece.

Ŷ

Do not use cracked or distorted saw blades. Do not use 
saw blades that are damaged or deformed.

 WARNING

Dust from certain paints, coatings, and materials may 
cause irritation or allergic reactions. Dust from wood 
such as oak, beech, MDF, and others are carcinogenic. 
Materials containing asbestos should only be worked on 

RUSURFHVVHGE\TXDOL¿HGVSHFLDOLVWRSHUDWRUV

 WARNING

Always wear safety goggles or safety glasses with 
side shields when operating the product. Failure to do 
so could result in objects being thrown into your eyes 
resulting in possible serious injury.

MAINTENANCE

 WARNING

The product should never be connected to a power 
supply when assembling parts, making adjustments, 
cleaning, performing maintenance, or when the product 
is not in use. Disconnecting the product will prevent 
accidental starting that could cause serious injury.

 WARNING

When servicing, use only original manufacturer’s 
replacement parts. Use of any other parts may create a 
hazard or cause product damage.

 WARNING

For greater safety and reliability, all repairs should be 
performed by an authorised Ryobi service centre.

 WARNING

Always wear safety goggles or safety glasses with 
side shields when operating the product. Failure to do 
so could result in objects being thrown into your eyes 
resulting in possible serious injury.

If the power supply cord is damaged, it must be replaced 
only by the manufacturer or by an authorised service centre 

to avoid a safety hazard. Contact authorised service centre.
When changing the saw blade, ensure that the saw blade 
holder is free of material residue, such as wood or metal 
shavings.

GENERAL

Avoid using solvents when cleaning plastic parts. Most 
plastics are susceptible to various types of commercial 
solvents and may be damaged by their use. Use clean 
cloths to remove dirt, carbon dust, etc.

 WARNING

'RQRWDWDQ\WLPHOHWEUDNHÀXLGVJDVROLQHSHWUROHXP

based products, and penetrating oils, come in contact 
with plastic parts. They contain chemicals that can 
damage, weaken, or destroy plastic.

(OHFWULFDO WRROV XVHG RQ ¿EHUJODVV PDWHULDO ZDOOERDUG

spackling compounds, or plaster are subject to accelerated 

ZHDUDQGSRVVLEOHSUHPDWXUHIDLOXUHEHFDXVHWKH¿EHUJODVV

chips and grindings are highly abrasive to bearings, 
brushes, and commutators. We do not recommend using 
the product for extended periods of time on these types 
of materials.

 WARNING

Do not use compressed air to blow dust from the product. 
This practice is dangerous and can cause dirt and grit to 
be blasted into someone’s eyes, causing injury.

LUBRICATION

All of the bearings in the product are lubricated with a 

VXI¿FLHQWDPRXQWRIKLJKJUDGHOXEULFDQWIRUWKHOLIHVSDQRI

the product under normal operating conditions. Therefore, 
no further lubrication is required.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing 
of as waste. The machine, accessories, and 
packaging should be sorted for environment-
friendly recycling.

SYMBOLS ON THE PRODUCT

Safety Alert

V

Volts

Hz

Hertz
Alternating current

W

Watts

n

o

No-load speed

PLQʚï

Revolutions or reciprocations per minute

CE Conformity

2

| English