Makita DJR188Z - Инструкция по эксплуатации - Страница 7

7 ENGLISH

Pull the switch trigger to light up the lamp. The lamp 

keeps on lighting while the switch trigger is being pulled. 

The lamp goes out approximately 10 seconds after 

releasing the switch trigger.

NOTE:

 Use a dry cloth to wipe the dirt off the lens of 

the lamp. Be careful not to scratch the lens of lamp, or 

it may lower the illumination.

NOTE:

 When the tool is overheated, the lamp blinks 

for one minute. In this case, cool down the tool before 

another operation.

ASSEMBLY

CAUTION:

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before carrying out any work on the tool.

Installing or removing the recipro 

saw blade

CAUTION:

Always clean out all chips or for-

eign matter adhering to the blade and around the 

blade clamp.

 Failure to do so may cause insufficient 

tightening of the blade, resulting in a serious injury.

To install the recipro saw blade, always make sure that 

the blade clamp lever (part of the blade clamp sleeve) 
is in released position   on the insulation cover before 

inserting the recipro saw blade. If the blade clamp lever 

is in fixed position, rotate the blade clamp lever in the 

direction of the arrow so that it can be locked at the 
released positon  .

► 

Fig.5:

1.

 Blade clamp lever 

2.

 Released position 

3.

 Fixed position

Insert the recipro saw blade into the blade clamp as far 

as it will go. The blade clamp sleeve rotates and fixes 

the recipro saw blade. Make sure that the recipro saw 

blade cannot be extracted even though you try to pull 

it out.

► 

Fig.6:

1.

 Recipro saw blade 

2.

 Blade clamp sleeve

CAUTION:

If you do not insert the recipro saw 

blade deep enough, the recipro saw blade may be 

ejected unexpectedly during operation.

 This can 

be extremely dangerous.

To remove the recipro saw blade, rotate the blade 

clamp lever in the direction of the arrow fully. The reci

-

pro saw blade is removed and the blade clamp lever is 

fixed at the released position 

.

► 

Fig.7:

1.

 Recipro saw blade 

2.

 Blade clamp lever

CAUTION:

Keep hands and fingers away from 

the lever during the switching operation. Failure 

to do so may cause personal injuries.

NOTE:

 If you remove the recipro saw blade without 

rotating the blade clamp lever fully, the lever may not 
be locked in the released position  . In this case, 

rotate the blade clamp lever fully again, then make 

sure that the blade clamp lever locked at the released 
position  .

NOTE:

 If the blade clamp lever is positioned inside 

the tool, switch on the tool just a second to let the 

blade out. Remove the battery cartridge from the tool 

before installing or removing the recipro saw blade.

OPERATION

CAUTION:

Always press the shoe firmly 

against the workpiece during operation.

 If the 

shoe is removed or held away from the workpiece 

during operation, strong vibration and/or twisting will 

be produced, causing the blade to snap dangerously.

CAUTION:

Always wear gloves to protect 

your hands from hot flying chips when cutting 

metal.

CAUTION:

Be sure to always wear suitable 

eye protection which conforms with current 

national standards.

CAUTION:

Always use a suitable coolant 

(cutting oil) when cutting metal.

 Failure to do so will 

cause premature blade wear.

CAUTION:

Do not quirk the blade during 

cutting. 

Press the shoe firmly against the workpiece. Do not 

allow the tool to bounce. Bring the recipro saw blade 

into light contact with the workpiece. First, make a pilot 

groove using a slower speed. Then use a faster speed 

to continue cutting.

► 

Fig.8

MAINTENANCE

CAUTION:

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before attempting to perform inspection or 

maintenance.

NOTICE:

Never use gasoline, benzine, thinner, 

alcohol or the like. Discoloration, deformation or 

cracks may result.

To maintain product SAFETY and RELIABILITY, 

repairs, any other maintenance or adjustment should 

be performed by Makita Authorized or Factory Service 

Centers, always using Makita replacement parts.