AEG US 900 XE - Инструкция по эксплуатации - Страница 10

8

GB

English

Always disconnect the plug from the socket before carrying out any 

work on the machine.
Only plug-in when machine is switched of.
Keep mains lead clear from working range of the machine. 

Always lead the cable away behind you.
Always use the protective shields on the machine.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft 

materials (wood, light building materials for walls). Harder 

materials (metals) must irst be drilled with a hole corresponding to 

the size of the saw blade.
When working in walls ceiling, or loor, take care to avoid electric 

cables and gas or waterpipes.
The dust produced when using this tool may be harmful to health. 

Do not inhale the dust. Wear a suitable dust protection mask. 

SPECIFIED CONDITIONS OF USE

This sabre saw cuts wood, plastic, and metal. It can cut straight 

lines, curves, and internal cut-outs. It cuts pipes and can cut lush 

to a surface.
Do not use this product in any other way as stated for normal use. 

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is in 

conformity with the following standards or standardized documents. 

EN 60745, EN 55014-1, EN 55014-2,  EN 61000-3-2, EN 61000-3-3,  

in accordance with the regulations 2006/42/EC, 2004/108/EC

MAINS CONNECTION

Connect only to single-phase a.c. current and only to the system 

voltage indicated on the rating plate.
It is also possible to connect to sockets without an earthing contact 

as the design conforms to safety class II. 

MAINTENANCE

The ventilation slots of the machine must be kept clear at all times.
Use only AEG accessories and AEG spare parts. Should components 

need to be replaced which have not been described, please contact 

one of our AEG service agents (see our list of guarantee/service 

addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type printed 

on the label and order the drawing at your local service agents or 

directly at: AEG Electric Tool, Max-Eyth-Straße 10,  

D-71364 Winnenden, Germany.

WARNING

The vibration emission level given in this information sheet has 

been measured in accordance with a standardised test given in  

EN 60 745 and may be used to compare one tool with another It 

may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main 

applications of the tool. However if the tool is used for diferent 

applications, with diferent accessories or poorly maintained, the 

vibration emission may difer. This may signiicantly increase the 

exposure level over the total working period.
An estimation of the level of exposure to vibration should also 

take into account the times when the tool is switched of or when 

it is running but not actually doing the job. This may signiicantly 

reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator 

from the efects of vibration such as: maintain the tool and the 

accessories, keep the hands warm, organisation of work patterns.

WARNING! 

Read all safety warnings and all instructions, including 

those given in the accompanying brochure.

 Failure to follow 

the warnings and instructions may result in electric shock, ire 

and/or serious injury.  

Save all warnings and instructions for 

future reference.

SAFETY INSTRUCTIONS

Wear ear protectors.

 Exposure to noise can cause hearing loss.

Hold power tool by insulated gripping surfaces when 

performing an operation where the cutting tool may 

contact hidden wiring or its own cord. 

 Contact with a “live” 

wire will also make exposed metal parts of the power tool  

“live” and shock the operator.
Appliances used at many diferent locations including open air 

should be connected via a residual current device of 30 mA or less.
Always wear goggles when using the machine. 
It is recommended to wear gloves, sturdy non slipping shoes and 

apron.
Sawdust and splinters must not be removed while the machine is 

running.

US 900 XE

Rated input  .................................................................. 900  W

Stroke rate under no–load  ..................................  0 - 3500  min 

-1

Lengths of stroke  ..........................................................  19  mm

Weight without cable ................................................... 2,9  kg

Noise/Vibration Information

Measured values determined according to EN 60745. 

Typically, the A-weighted noise levels of the tool are: 

Sound pressure level (K = 3 dB(A))  ............................ 89,5   dB (A)

Sound power level (K = 3 dB(A))  .............................. 100,5   dB (A)

Wear ear protection!

Total vibration values (vector sum in the three axes) 

determined according to EN 60745. 

Sawing of wood 

Vibration emission value a

h

  ......................................... 19,1   m/s

2

Uncertainty K   ............................................................... 1,5  m/s

2

Rainer Kumpf

Manager Product Development

Authorized to compile the technical ile.

Winnenden, 2010-07-30

TECHNICAL DATA  

Reciprocating saw