AEG US 400 XE - Инструкция по эксплуатации - Страница 8

6

7

GB

English

TECHNICAL DATA

When working in walls ceiling, or fl oor, take care to avoid electric 

cables and gas or waterpipes.

The dust produced when using this tool may be harmful to health. 

Do not inhale the dust. Wear a suitable dust protection mask.

This sabre saw cuts wood, plastic, and metal. It can cut

straight lines, curves, and internal cut-outs. It cuts pipes and

can cut fl ush to a surface.

Do not use this product in any other way as stated for normal use.

We declare under our sole responsibility that this product is

in conformity with the following standards or standardized

documents.

EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-2,

EN 61000-3-3, in accordance with the regulations 98/37/EG, 

2004/108/EG

Connect only to single-phase a.c. current and only to the

system voltage indicated on the rating plate. It is also possible

to connect to sockets without an earthing contact as the design

conforms to safety class II.

The ventilation slots of the machine must be kept clear at all times.

Use only Milwaukee accessories and Milwaukee spare parts. 

Should components need to be replaced which have not been 

described, please contact one of our Milwaukee service agents 

(see our list of guarantee/service addresses).

If needed, an exploded view of the tool can be ordered.

Please state the Article No. as well as the machine type printed 

on the label and order the drawing at your local service agents or 

directly at: Milwaukee Electric Tool, Max-Eyth-Straße 10,

D-71364 Winnenden, Germany.

Please read the instructions carefully before 

starting the machine. 

Always disconnect the plug from the socket 

before carrying out any work on the machine.

Do not dispose of electric tools together with household 

waste material! In observance of European Directive 

2002/96/EC on waste electrical  and electronic 

equipment and its implementation in accordance with 

national law, electric tools that have reached the end of 

their life must be collected separately and returned to 

an environmentally compatible recycling facility.

WARNING! 

Read all safety warnings and all instructions, including those 

given in the accompanying brochure

. Failure to follow the 

warnings and instructions may result in electric shock, fi re and/or 

serious injury.  

Save all warnings and instructions for future 

reference.

Wear ear protectors. 

Exposure to noise can cause hearing loss.

Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory

may contact hidden wiring or its own cord. 

Cutting accessory 

contacting a „live“ wire may make exposed metal parts of the 

power tool „live“ and could give the operator an electric shock.
Appliances used at many different locations including open air 

should be connected via a residual current device of 30 mA or less.

Always wear goggles when using the machine. 

It is recommended to wear gloves, sturdy non slipping shoes and 

apron.

Sawdust and splinters must not be removed while the machine is 

running.

Always disconnect the plug from the socket before carrying out 

any work on the machine.
Only plug-in when machine is switched off.

Keep mains lead clear from working range of the machine.

Always lead the cable away behind you.

Always use the protective shields on the machine.

Do not use cracked or distorted saw blades.

Plunge cuts without pre–drilling a hole are possible with soft

materials (wood, light building materials for walls). Harder

materials (metals) must fi rst be drilled with a hole corresponding to 

the size of the saw blade.

US 400 XE

Rated input ................................................................. 400  W

Stroke rate under no–load  .................................... 0-3500  /min

Lengths of stroke .......................................................... 13  mm

Weight without cable  .................................................. 1,7  kg

Noise/Vibration Information

Measured values determined according to EN 60745.

Typically, the A-weighted noise levels of the tool are:

Sound pressure level (K = 3 dB(A)) .......................... 83  dB(A)

Sound power level (K = 3 dB(A)) .............................. 94  dB(A)

Wear ear protection!

Total vibration values (vector sum in the three axes)

determined according to EN 60745.

Sawing of wood

Vibration emission value a

h 

................................... 18,3  m/s

2

Uncertainty K ........................................................... 1,5  m/s

2

WARNING

The vibration emission level given in this information sheet has 

been measured in accordance with a standardised test given in 

EN 60 745 and may be used to compare one tool with another. 

It may be used for a preliminary assessment of exposure.

The declared vibration emission level represents the main 

applications of the tool. However if the tool is used for different 

applications, with different accessories or poorly maintained, the 

vibration emission may differ. This may signifi cantly increase the 

exposure level over the total working period.

An estimation of the level of exposure to vibration should also take 

into account the times when the tool is switched off or when it is 

running but not actually doing the job. This may signifi cantly reduce 

the exposure level over the total working period.

Identify additional safety measures to protect the operator from the 

effects of vibration such as: maintain the tool and the accessories, 

keep the hands warm, organisation of work patterns.

SAFETY INSTRUCTIONS

SPECIFIED CONDITIONS OF USE

EC-DECLARATION OF CONFORMITY

MAINS CONNECTION

MAINTENANCE

SYMBOLS

Rainer Kumpf

Manager Product Development

Winnenden, 2009-07-02