RCA LED55C55R120Q - Инструкция

HDMI 1/DVI, 2

COMPONENT Y, Pb, Pr

L-AUDIO-R

COMPOSITE

L-AUDIO-R

Jacks

Cables

Further
Information

Audio Cable

COMPONENT video cable

Video/Audio cable

See the below

Go to page 5

Go to page 5

HDMI cable

HDMI-DVI cable

Longer side

Remote Control Instructions

Learning about Remote Control

Power/Standby Indicator: Light up in red when the TV is in standby

mode. Light out when the TV is on.

Remote Control Sensor: Remote control IR sensor, which receives

infrared ray sent by remote control.

Keypad and Front Panel

Keypad Buttons

If you cannot locate your remote, you can use the keypad buttons on

your TV to operate many TV features.

Front Panel

About remote control working distance and angle, see the right side.

INPUT:

Displays the Source Select List.

MENU:

Displays the TV Main Menu.

CH :

Scans up through the channel list. In the TV menu system, it acts

like the up arrow on the remote control and can be used to select

menu options.

CH :

Scans down through the channel list. In the TV menu system,

it acts like the down arrow on the remote control and can be used to

select menu options.

VOL+:

Increases the volume. In the TV menu system, it acts like the

right arrow on the remote control and can be used to select menu

options.

VOL-:

Decreases the volume. In the TV menu system, it acts like the

left arrow on the remote control and can be used to select menu

options.

POWER ( ):

Turns the TV on and off.

Inserting Batteries in the Remote

• Remove the cover of battery cabin on the back of the remote control

by lifting the cover.

• Insert two AAA batteries, making sure the polarities (+ and -) are

aligned correctly.

• Place the cover back.

• Are the polarities (+, -) correct?

• Are the batteries worn out?

• Is there an AC power failure?

• Is the power cord plugged in?

• Is there any interference or block near the remote control sensor?

If the remote control does not work, check these points:

• Used batteries should be recycled.

• Keep out of children’s reach.

• DO NOT use new and old batteries together.

• Change both the batteries at the same time.

• When not using the remote control for a long time, remove the

batteries from the unit.

CAUTION:

Universal Remote Control Code List

For Universal Remote Control brands listed below, please use ac

companying codes and refer to your Universal Remote Control User

Manual for basic Instruction for changing TV code to operate the TV

model.

Codes for DIRECTV: 0178, 10178

Codes for Time Warner Cable: 0178, 10178

Codes for Cox Communications: 0178

Codes for Comcast: 10178

Codes for Dish Network: 627

Codes for Fios Verizon: 0205, 0057, 0493, 0775

Remote Control Reception Angle

Use your remote control within the distance and angle range shown

below.

Remote Control Buttons

MUTE ( ):

Reduces the TV volume to its

minimum level.

Press again to restore the volume.

POWER ( ):

Turns the TV on or off.

CH.LIST:

Displays the channel list.

FAV.:

Adds the current channel to your

favorite list, or erases the current channel from

your favorite list (if this channel is a favorite

channel already).

FAV.+ or FAV.- :

Scans up or down through

the current favorite channel list.

Numeric Buttons:

Use these buttons to enter

numbers.

“ ”:

To enter a digital channel with a sub-

channel, enter the main channel; then, press

this button to enter the sub-channel and press

ENTER.

Recall ( ):

Returns to the previous channel.

EPG:

Shows Electronic Program Guide (see

page 8).

I

NPUT:

Accesses the available input channels

(TV, AV, Component, HDMI 1/2, Media). Use

the arrows to highlight options, and press

ENTER to select.

Arrows ( / / / ):

Uses the four arrows

to highlight different items in the TV menu or

change the value. The up/down arrow can also

work as CH /CH button, and the left/right

arrow can also work as VOL-/VOL+ button.

ENTER:

Enter and confirm button.

MENU:

Accesses the Main Menu, or return to

the upper level of a sub-menu.

FREEZE:

Freeze the current screen frame,

press again to return to normal.

DISPLAY:

Displays the Channel Bar (see

page 7).

EXIT:

Exits the current menu or function.

VOL+ or VOL-:

Increases or decreases the TV

6

4

Step Three

Take the base. Please align four holes of the base and four screwholes

of the neck, insert the base to the neck, and then insert the 4 screws

and tighten them.

AC

100-120V

60Hz

ANT/ CABLE

AC Power Cord

(Connect after all the other connections are done.)

Antenna

Cable TV

Or

WALL

OUTLET

The first step in connecting your TV is obtaining the signal. Your TV

LED55C55R120Q has a back panel, which allows you to receive

analog and/or digital television channels via ANT/CABLE jack.

Before connecting your TV, determine using an antenna or a cable

service to obtain the signal.

A. Antenna

Connect the antenna to TV via coaxial cable on ANT/CABLE jack

of the back panel. You are ready to receive air local digital and

analog channels.

B. Cable TV service

Connect the cable TV wall jack to TV via coaxial cable on

ANT/CABLE jack of the back panel. You are ready to receive

off-air local digital and analog channels.

C. Set-Top Box

If you use a set-top box, you may need to call your cable company

or satellite service provider, which use a special connection, please

refer to the user’s guide of set-top box.

Note: Do not plug the AC cord until you have accomplished

all the connections.

RS01TM412H

Pedestal
Screws

Quantity

Part #

6pcs

M4 x 12mm

TV Signal Connection

Side Panel Connections

Cable Connections

Choose Your Connections

TV LED55C55R120Q supports various connections to other

devices (such as DVD, VCR, Set-top box, etc.). Please follow the

table to choose the cables which adapt to your device.

Note:

HDMI, the HDMI logo, and High-Definition Multimedia Interface

are trademarks or registered trademarks of HDMI Licensing LLC
Caution:

Unplug the AC cord when you connect other devices to TV.

Connecting AV Composite device

(Good Video Quality)

Composite connector will be shared with Component Y connector.

To connect a composite AV device, such as a DVD player, follow these

steps:

1.Connect the COMPOSITE jack on the side of TV to the video output

jacks of device via video cable (yellow).

2.Connect the L-AUDIO-R jacks on the side of TV to the audio

output jacks of device via audio cable.

Notice the left channel jack and plugs are white and the right

channel jack and plugs are red.

Composite Video Connection

The picture below is an example of a connection using the
composite video jack.

The back of TV

Note: AV signal belongs to composite video. This kind of video signal

has regular good display quality.

5

TV Jacks Explanation

Connecting YPbPr Component device

(Better Video Quality)

To connect a component device, such as a DVD player, follow these

steps:

1.Connect the COMPONENT IN Y/Pb/Pr jack on the side of TV to the

video output jacks of device via video cable (green, blue and red).

2.Connect the L-AUDIO-R jacks on the side of TV to the audio

output jacks of device via audio cable.

Notice the left channel jack and plugs are white and the right channel

jack and plugs are red.

Component Video Connection

The picture below is an example of a connection using the component

video jack.

Note: Y/Pb/Pr jacks are component video. This kind of video signal has

better display quality.

Connecting HDMI device

(Best Video Quality)

HDMI Connection

The picture below is an example of a connection using the HDMI video

jack.

To connect a HDMI device, such as a DVD player, please Connect the

HDMI1/DVI, 2 jack on the side of TV to the output jacks of device via

HDMI cable.

The back of TV

To connect a DVI device, via DVI port of PC or Device and HDMI

jack of TV:

1. Connect the HDMI1/DVI jack on the side of TV to the DVI port of

PC via HDMI-DVI cable.

2. Connect the L-AUDIO-R jack on the side of TV to the audio

output jack of computer with audio cable (dual-channel RCA jacks

to 3.5mm stereo jack or the L-AUDIO-R jack).

Note: 1. HDMI (High-Definition Multimedia Interface) is a compact

audio/video interface for transmitting uncompressed digital data. It

carries the audio and video signal via the same cable and has the best

display quality.

2. HDMI-DVI cable transfers only video signal from DVI port of

DVI device to HDMI jack of TV. For audio signal, please connect audio

output to L-AUDIO-R jack on TV back panel.

How to Obtain Various Kinds of Input
Sources

After connection is done, press INPUT button on remote control or TV

top panel to choose the input source you need. See page 7, Basic

Operation of TV.

HEAD PHONE:

Connect a 3.5mm headphone for

personal audio.

USB:

Connect your USB storage device to enjoy music/

photo files on your TV. (Also used for service purpose).

HDMI1/DVI, 2:

(High-Definition Multimedia Interface)

It provides an uncompressed digital connection that
carries both video and audio data by way of an integrated
mini-plug cable.

COMPONENT Y/Pb/Pr:

Connect a device that has

component video jacks, such as a DVD player. To access
device connected to the Y/Pb/Pr jack, press the INPUT
button on your remote; then press the up/down arrow to
select Component. Press the ENTER button at last to
confirm.

• Y/Pb/Pr (Component Video):

They provide good

picture quality because the video signal is separated into
three components. Use three video-grade or component

video cables for the connection. When using Y/Pb/Pr,

make sure you connect left and right audio cables to the
AUDIO IN R/L jacks.

L-AUDIO-R, COMPOSITE:

Connect an AV device that has composite

video jacks, such as a VCR or a DVD player. To access device connected
to these jacks, press the INPUT button on your remote; then press the
up/down arrow to select AV. Press the ENTER button at last to confirm.

• AUDIO IN L:

Left audio channel connection. The left audio

connector is usually white. For mono audio sources, be sure to use the
left AUDIO INPUT.

• AUDIO IN R:

Right audio channel connection. The right audio

connector is usually red.

ANT/CABLE:

Connect to receive the signal from your antenna or cable

via coaxial cable.

Digital Audio out:

Connect a coaxial cable for digital audio output.

7

Step Two

Please select the TV installation mode, press

the up/down arrow select the mode you

need: Home, Retail. If you select Home

mode, the next option is step three. If you

select Retail mode, please refer the step four.

Initial Setup

If it is the first time you turn on your TV, or you have done Clear

Channel List option (see page 10), the initial setup menu appears

automatically.

Step One

Please select Menu Language, press the

up/down arrow select the language you

need. Available languages: English, Spanish

and French.

Step Four

To choose your TV tuner signal type, press the up/down arrow select

the signal type: Air, Cable.

Note: please select TV signal type according to the antenna or cable

closed circuit TV you use.

Step Three

Please choose between Energy Saving and

Dynamic mode. You can save more energy

with Energy Saving.

What to notice:

1. The channel search access starts from the Analog TV channel

searching and ends at Digital TV channel searching.

2. The channels that have been found will be stored automatically.

3. You can press MENU button to skip analog/digital channel

searching.

4. You can press ENTER/EXIT button to end the channel searching.

Step Five

If you accomplish the initial setup, the TV will search channels

automatically.

NOTE : The keys not listed are for DVD control, they are not available

for this TV model.

Tuning To Analog Channels

An analog channel has a channel number beginning with “A”. Input the

digital number with numeric buttons directly and press ENTER button

to confirm.

For example, to watch analog channel “A51”, press “5”, “1”, “ENTER”

on remote control in sequence.

Note: Although there is no analog TV signal available in America, we

reserve ATV functions for some expansible use.

Tuning To Digital Channels

A digital channel has a channel number beginning with “D”. Input the

main digital number with numeric buttons directly, then press “ ”

button on remote control, and input the sub number at last.

For example, to watch analog channel “D31-1”, press “3”, “1”, “ ”,

“1”, “ENTER” on remote control in sequence.

Choosing TV Channel

Basic Operations

Turning On and Off

Connect the AC cord to power the LED LCD TV. At this time the TV

will enter standby mode and power indicator will turn red. Use Power

button ( ) on the top panel of TV or on the remote control to turn on

the TV. After switching off the TV for 5 seconds, you can turn on TV

again.

volume.

CH or CH :

Scans up or down through the current channel list.

Press once to change the channel up or down; press and hold to

continue changing channels.

PICTURE:

Switches between the preset picture mode (see page 8).

SOUND:

Switches between the preset sound mode (see page 8).

SLEEP:

Selects the sleep timer, after which the TV will shut off

automatically.

ASPECT:

Switches between the preset screen size mode (see page 8).

CC:

Selects the closed caption.

MTS:

Selects the multi-channel television sound.

Selecting Input Source

Press INPUT button on remote control to

display Source Select list.

Use up/down arrows to highlight the source

you need and press ENTER to confirm.

Media

Source Select

TV

AV

HDMI 1

Component

HDMI 2

Changing Channels Directly

You can use CH button to increase channel number and CH to

decrease channel number. When no OSD (On Screen Display) is used,

the up/down arrows can also work as CH /CH buttons.

Channel Bar

Press the DISPLAY button on the remote control, the channel bar will

appear on the top right corner of the screen. It displays the current

channel’s information. The following list describes the items on the

channel bar.

Mono

A2

480i

Air

Oct-31 23.14 Mon

MTV

ATV

English

KOCE-HD

D50

-

1

1080i

Oct-31 23:14 Mon

Air

DTV

A2/D50-1

If the channel is analog, A is displayed. If it’s a

digital channel, D is displayed. For example, in the

pictures above, A2 is an analog channel, and

D50-1 is a digital channel ( -1 is a sub-channel

number).

MTV/KOCE-HD

Displays the channel label.

Mono/English

Displays whether the current channel is being

broadcasted in stereo or mono. If the current

channel is digital, this space will be SAP (Second

Audio Program) language.

480i/1080i

Displays the signal resolution.

16:9/CC/TV-PG

Displays the screen aspect ratio, closed caption

and TV rating level of the current program or

channel. These are only available for digital

channels.

Oct-31 23:14 Mon

Displays current date and time.

Adjusting Volume

Press the VOL+/VOL- button on the remote control to adjust the

volume. If you want to switch sound off, press MUTE ( ). When OSD

(On Screen Display) is not used, the arrows left/right can also work as

VOL-/VOL+ buttons.

RS01PWA414HT

Pedestal
Screws

Quantity

Part #

4pcs

M4 x 14mm

Please take note of the base direction:

The bottom view of the TV

(Front cabinet faces down)

Remote Control Sensor

Power/Standby Indicator

20 feet

Audio

L

R

Audio

L

R

Video

Y

Pb

Pr

HDMI

The output panel of other device

The back of TV

Audio

L

R

Audio

L

R

Video

Y

Pb

Pr

HDMI

The output panel of other device

Audio L

R

Audio L

R

Y

Pb

Pr

Video

HDMI

The output panel

of HDMI device

The output panel of

other AV device

PC

DVI

Speaker or headphone

Audio Out L

R

DVI

Remote control part number

RE20QP80

CH LIST

.

PICTURE

SOUND

Initial Setup

Initial Setup Wizard will assist you in configuring

basic Settings

Press ENTER/RIGHT to go to next page

MOVE

SELECT

: Exit

Next

AUTO CHANNEL SEARCH

Now Searching... Please Wait...

Press MENU to skip analog signal scanning and

ENTER/EXIT to exit

MOVE

SELECT

: Exit

Return

Analog Channels Found: 1

Digital Channels Found: 0

3%

PICTURE

SOUND

CHANNEL PARENTAL

SETUP

OTHERS

Longer side