Ryobi R18SV7 - Инструкция по эксплуатации - Страница 4

2

BATTERY AND CHARGER SAFETY

■

Connect and disconnect the battery pack properly.

●

To install battery pack:

–

Place the battery pack on the product.

–

Make sure the latches on each side of the 

battery pack snap into place and the battery 

pack is secured on the product before beginning 

operation.

●

To remove battery pack:

–

Depress the latches on the side of the battery 

pack.

–

Remove the battery pack from the product.

■

A battery operated product with integral batteries or a 

separate battery pack must be recharged only with the 

specified charger for the battery. A charger that may be 

suitable for one type of battery may create a risk of fire 

when used with another battery.

■

Do not expose charger to wet or damp conditions.

■

Do not place batteries near fire or heat. They may 

explode.

■

Do not expose a battery pack or tool to fire or excessive 

temperature. Exposure to fire or temperature above 

130 °C may cause explosion.

■

Do not place product near any heat sources such as 

radiators, heat registers, stoves, or other products 

(including amplifiers) that produce heat.

■

Batteries can explode in the presence of a source 

of ignition, such as a pilot light. To reduce the risk of 

serious personal injury, never use any cordless product 

in the presence of open flame. An exploded battery 

can propel debris and chemicals. If exposed, flush with 

water immediately.

■

Battery products do not have to be plugged into an 

electrical outlet; therefore, they are always in operating 

condition. Be aware of possible hazards when not using 

your battery product or when changing accessories. 

Following the rule will reduce the risk of electric shock, 

fire, or serious personal injury.

■

Danger of explosion if battery is incorrectly replaced. 

Replace only with the same or equivalent type.

■

Use of an attachment not recommended or sold by the 

battery charger manufacturer may result in a risk of fire, 

electric shock, or injuries to person.

■

When battery pack is not in use, keep it away from 

other metal objects like paper clips, coins, keys, nails, 

screws, or other small metal objects that can make a 

connection from one terminal to another. Shorting the 

battery terminals together may cause sparks, burns, or 

a fire.

■

To reduce risk of damage to charger body and cord, pull 

by charger plug rather than cord when disconnecting 

charger.

■

For best results, your battery product should be 

charged in a location where the temperature is more 

than 10°C (50°F) but less than 38°C (100°F). To reduce 

the risk of serious personal injury, do not store outside 

or in vehicles.

■

Follow all charging instructions and do not charge the 

battery pack or tool outside the temperature range 

specified in the instructions. Charging improperly or at 

temperatures outside the specified range may damage 

the battery and increase the risk of fire.

■

Do not charge battery product in a damp or wet location. 

Following the rule will reduce the risk of electric shock.

■

Make sure cord is located so that it will not be stepped 

on, tripped over, or otherwise subjected to damage and 

stress.

■

Do not crush, drop or damage battery pack. Do not use 

a battery pack or charger that has been dropped or 

received a sharp blow. A damaged battery is subject to 

explosion. Properly dispose of a dropped or damaged 

battery immediately.

■

An extension cord should not be used unless absolutely 

necessary. Use of improper extension cord could result 

in a risk of fire and electric shock. If extension cord must 

be used, make sure:

a)  That pins on plug of extension cord are the same 

number, size and shape as those of plug on 

charger.

b)  That extension cord is properly wired and in good 

electrical condition.

■

Do not operate charger with a damaged cord or plug. 

If damaged, have it replaced immediately by a qualified 

serviceman.

■

Do not operate charger if it has received a sharp blow, 

been dropped, or otherwise damaged in any way; take 

it to a qualified serviceman.

■

Do not disassemble charger; take it to a qualified 

serviceman when service or repair is required. Incorrect 

reassembly may result in a risk of electric shock or fire.

■

To reduce risk of electric shock, unplug the charger 

from outlet before attempting any maintenance or 

cleaning. Turning off controls will not reduce this risk.

■

Disconnect charger from power supply when not in use.

■

Risk of electric shock. Do not touch uninsulated portion 

of output connector or uninsulated battery terminal.

■

Do not use a battery pack or tool that is damaged or 

modified. Damaged or modified batteries may exhibit 

unpredictable behavior resulting in fire, explosion or 

risk of injury.

■

Rechargeable batteries are to be removed from the 

appliance before being charged.

■

Different types of batteries or new and used batteries 

are not to be mixed.

■

Batteries are to be inserted with the correct polarity.

■

Exhausted batteries are to be removed from the 

appliance and safely disposed of.

■

If the appliance is to be stored unused for a long period, 

the batteries should be removed.

■

The supply terminals are not to be short-circuited.

■

Under extreme usage or temperature conditions, 

battery leakage may occur. If liquid comes in contact 

with your skin, wash immediately with soap and water. 

If liquid gets into your eyes, flush them with clean water 

for at least 10 minutes, then seek immediate medical 

attention. Following the rule will reduce the risk of 

serious personal injury.

■

Do not dispose of used battery packs in the household 

refuse or by burning them. Take them to an appropriate 

disposal/collection site.

ADDITIONAL BATTERY SAFETY WARNINGS

 WARNING

To reduce the risk of fire, personal injury, and product 

damage due to a short circuit, never immerse your 

tool, battery pack or charger in fluid or allow a fluid to 

flow inside them. Corrosive or conductive fluids, such 

as seawater, certain industrial chemicals, and bleach 

or bleach-containing products, etc., can cause a short 

circuit.