BRAYER BR4200 - Инструкция по эксплуатации - Страница 5

8

9

EN

EN

USING  THE ATTACHMENTS
Floor/carpet brush (1)

When using the brush (1) set the switch (2) to the 

necessary «FLOOR/CARPET» position (pic. 1).

Combined crevice nozzle (26)

The combined crevice nozzle (26) can be used for 

cleaning radiators, crevices or spaces between 

cushions, as well as for collecting dust from furniture 

surface. The pile on the brush prevents damage of 

polished furniture surfaces. While cleaning, set the 

brush to the required position.

Furniture/furniture upholstery brush (27)

The attachment (27) is intended for cleaning fabric 

surfaces of upholstered furniture and for collecting 

dust from furniture surface, the pile on the brush (27) 

prevents damage of polished furniture surface. During 

operation install the brush on the attachment (27).

ASSEMBLING THE VACUUM CLEANER

Attaching and removing the flexible hose (7)

• 

Insert the flexible hose (7) ending (8) into the air inlet 

(10) until the locks (9) catch.

• 

To remove the flexible hose (7), press the locks (9) 

and detach the ending (8) from the air inlet (10).

Attaching the telescopic pipe (4) and the 

attachments

• 

Attach the telescopic extension pipe (4) to the flexible 

hose handle (5).

•  Extend the lower part of the telescopic extension 

pipe (4) to the required length, having preliminarily 

pressed the lock (3) (pic. 2).

• 

Choose the necessary attachment: floor/carpet brush 

(1), combined crevice nozzle (26) or parquet/laminate 

floor attachment (27) - and attach it to the telescopic 

extension pipe (4).

•  You can attach the combined crevice nozzle (26) to 

the flexible hose handle (5).

ATTENTION!

•  Do not use the vacuum cleaner in places where 

aerosols are used or sprayed and in proximity to 

highly inflammable liquids, do not use the vacuum 

cleaner in the places where such liquids are stored.

•  The vacuum cleaner is not intended for collecting 

water or any other liquids; do not use it for collecting 

burning or smoking cigarettes or cinders.

•  Do not use the vacuum cleaner for collecting dust of 

plaster, concrete, flour or ashes.

• 

Take sharp objects away from the floor before 

cleaning to prevent damage to the unit.

•  If the suction power of the vacuum cleaner decreases 

rapidly while cleaning, switch it off immediately, 

unplug it and check the telescopic pipe (4) or 

the flexible hose (7) for obstruction. Remove the 

obstruction, after that you can resume cleaning.

USING THE VACUUM CLEANER

The dust bin (11) is equipped with the cyclonic filter (20) 

which sieves out garbage and dust from the ingoing air, 

and the inlet HEPA (19) filter fully retains the finest dust 

particles.

Note:

 provide that the HEPA filter (19) is always clean, 

because the overall performance of the vacuum cleaner 

depends on it.

Attention! 

Before switching on and using the vacuum cleaner, 

make sure that the HEPA filter (19), the separator (20), 

the dust bin (11) and the outlet filter (17) are installed 

properly.
•  Take the power plug and unwind the power cord to 

the required length, connect the power plug to the 

mains socket.

•  The yellow mark on the power cord indicates the 

maximum cord length. Do not pull out the power cord 

further than the red mark.

• 

Press the on/off button (16) to switch the vacuum 

cleaner on.

•  While cleaning, you can control the suction power 

using the manual suction power control (6) on the 

flexible hose handle (5) (pic. 3).

• 

After you finish cleaning, switch the vacuum cleaner 

off by pressing the on/off button (16) and unplug it.

• 

To wind the power cord, press the button (14); keep a 

hold of the winding cord with your hand. 

•  If you have to make a break during the cleaning, 

switch the vacuum cleaner off by pressing the button 

(16) and install the brush (1) to the brush storage 

(15) (pic. 4).

ATTENTION!
Before changing the attachments or cleaning the 

dust bin (11), switch the vacuum cleaner off by 

pressing the on/off button (16) and unplug it.

CLEANING AND  MAINTENANCE
Cleaning the dust bin (11)

•  It is recommended to remove garbage and dust from 

the dust bin (11) after every room cleaning.

• 

Switch the vacuum cleaner off by pressing the on/off 

button (16) and unplug it.

•  Holding the handle (12), press the lock (13) and 

remove the dust bin (11) (pic. 5).

•  Place the dust bin (11) over a garbage bin.

•  Pull the lock (24) and open the lower lid (25) (pic. 6).

•  Remove accumulated dust and garbage from dust 

bin (11).

•  Close the lid (25).

•  Install the dust bin (11) back to its place and make 

sure that the dust bin (11) is fixed properly.