Пылесос Vitek VT-8114 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
5
ENGLISH
•
To clean the cloth dustbag
(20)
place it
above the trash bin and remove the plastic
clamp (25). After cleaning install the plastic
clamp (25) back to its place.
•
To install the dustbag
(20)
back to its place,
insert the dustbag holder (
18
) into the
notches of the locks (
19
) as far as it will go.
•
Close the dustbag compartment lid (
13
).
Note:
Always make sure that the dustbag holder
(18) and the dustbag (20) are installed prop-
erly before closing the dustbag compartment
lid (13). After every installation carefully tuck
the dustbag (20) edges into the dustbag com-
partment and then close the lid (13).
USING THE VACUUM CLEANER
Safety measures
•
Do not use the vacuum cleaner near hot sur-
faces, such as ashtrays and in places where
inflammable liquids are stored.
•
Take sharp objects away from the floor before
cleaning to prevent damage to the unit.
•
If the suction power of the vacuum cleaner
decreases rapidly while cleaning, switch it
off immediately and check the telescopic
pipe and the flexible hose for obstruction.
Switch the vacuum cleaner off, then unplug
it, remove the obstruction and only after that
continue cleaning.
OPERATION
Attention! Always switch the vacuum
cleaner on only with the dustbag (20) and
inlet (21) and outlet (24) filters installed.
Always make sure that the filters are
installed properly.
•
Before using the unit, unwind the power cord
to the required length and insert the power
plug into the mains socket.
•
The yellow mark on the power cord indicates
the maximum cord length. Do not unwind the
power cord further than the red mark.
•
Press the ON/OFF button (
17
) to switch the
vacuum cleaner on.
•
During the operation you can control the
suction power using the suction power con-
trol (
16
) and the manual suction power con-
trol (
6
) on the flexible hose handle (
5
).
•
After room cleaning switch the vacuum
cleaner off by pressing the ON/OFF but-
ton (
17
) and unplug the unit.
•
To wind the cord press the cord winding but-
ton (
15
), hold the winding cord with your hand
to avoid its whipping and damage.
CLEANING AND CARE
•
If the full dustbag indicator (
14
) turns red dur-
ing operation, clean up the cloth dustbag.
•
Before cleaning or replacing the dustbag (
20
)
switch the vacuum cleaner off and unplug it.
To clean the cloth dustbag
(20)
place it
above the trash bin and remove the plastic
clamp (25). If necessary, wash the cloth dust-
bag with warm water and neutral detergent
and dry thoroughly, after that install the plastic
clamp back to its place.
•
Provide that the inlet filter (
21
) and the outlet
foam filter (
24
) are always clean, because the
overall performance of the vacuum cleaner
depends on it; clean the filters no less than
3-4 times a year, and more often at severe
obstruction.
Cleaning the inlet filter (21)
•
Switch the vacuum cleaner off and unplug it.
•
Open the dustbag compartment lid (
13
) by press-
ing the lock (
12
). Remove the dustbag (
20
).
•
Take the inlet filter
(21
) and remove it from the
clamp (22) by pulling it upwards.
•
Wash the inlet filter (
21
) with warm water,
dry thoroughly and install it into the grid
holder (
22
).
•
Install the dustbag (
20
) back to its place.
•
Close the dustbag compartment lid (
13
).
Cleaning the outlet filters (24)
•
Switch the vacuum cleaner off and unplug it.
•
Remove the outlet filter grid (
23
) by press-
ing the lock (28). Remove the outlet filter (
24
)
from the grid (
23
).
•
Wash the filter (
24
) under slightly warm water
jet. Do not wash the filters in a dishwashing
machine.
•
Dry the filter (
24
). Do not dry the filters with
a hairdryer.
•
Install the filter (
24
) into the grid (
23
) accord-
ing to its form.
•
Install the outlet filter grid (
23
) with the
installed filter (
24
) back to its place.
Notes:
–
Before installing the filters (21, 24) make sure
that they are dry.
–
Do not dry the filters (21, 24) with a hairdryer.
IM VT-8114.indd 5
28.07.2016 10:28:38
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)
