VITEK VT-1832 R/B - Инструкция по эксплуатации - Страница 6

6

 ENGLISH

Never use the vacuum cleaner to pick up wa-

• 

ter or other liquids, burning or smoke-emit-
ting cigarettes, matches, smoldering ashes 
or fine dust such as from plaster, cement, 
flour or cinder.
Do not use the vacuum cleaner: 

• 

-   without the container for dust and rubbish

; 

-   without the removable details;
-   output НЕРА-filter and all foam filters are not 

installed.
Check the power cord and the power plug 

• 

for damages regularly. If there are some 
damages in the power cord, the power 
plug, or if the unit malfunctions, apply to the 
authorized service center.

The unit is intended for household usage only; 

• 

commercial usage of the vacuum cleaner is 
prohibited.

STORE THE INSTRUCTIONS IN A CONVENIENT 
PLACE

SAFETY PRECAUTIONS

Do not use the vacuum cleaner in the imme-

• 

diate vicinity of very hot surfaces, next to ash 
trays, or where flammable liquids are stored.
Before cleaning, remove sharp objects from 

• 

the floor to avoid damage of the filters.
If suction power decreases abruptly while 

• 

cleaning, immediately turn off the vacuum 
cleaner and check the telescoping tube or 
flexible hose for foreign objects. Turn off the 
vacuum cleaner, and then unplug it from the 
power outlet. Clear the obstruction and only 
then proceed with cleaning.

Assembling the vacuum cleaner

-   Unpack the vacuum cleaner and check it for 

damages. If there are any damages in the 
unit, do not use it.

-   Before turning on the vacuum cleaner, make 

sure that the voltage of the mains corresponds 
to the voltage of the vacuum cleaner.

-   Always turn off the vacuum cleaner and 

unplug it from the outlet before changing the 
brushes/attachments, and before performing 
maintenance.

Filling the container with water for dust and 
rubbish collection (9)

Open the lid (5), by pulling the lid opening 

• 

button (7) (pic.1).

Take the side edges on the container for dust 

• 

and rubbish (9) remove it from the body of the 
vacuum cleaner (pic. 2).
Remove the filter unit (10), holding the handle 

• 

on the separator lid (21) (pic. 3).
Fill the container (9) with water until the MAX 

• 

mark.

Note: 

Necessary quantity of water is 1300 ml.

Put the filter unit (10) into the container (9).

• 

Put the container (9) into the body of the vac-

• 

uum cleaner.
Check whether the container (9) and the filter 

• 

unit (10) are set properly. 
Close the lid (5). 

• 

Note: 
-   Do not exceed the MAX mark.
-   Do not use the vacuum cleaner if there is no 

water in the container (9).

Attaching and removing the flexible hose

(13)

Insert the end of the flexible hose (11) in the 

• 

air inlet (8). 

Insert the hose until a click, which confirms 

• 

proper connection (pic. 4).

To remove the flexible hose end press the 

• 

clamp 

(12) and disconnect the hose.

Attaching the telescoping extension pipe 
(15) and the attachments

Attach the telescoping extension pipe (15) to 

• 

the flexible hose handle (14)

. 

Extend the lower part of the telescoping pipe 

• 

to the desired length by pressing the clamp 
button (pic.5).
Select the desired attachment

• 

: carpet/

floor brush (16), small brush (25), crevice 
attachment (26), 

attachment for furniture 

surface

 (27) 

and connect it to the telescoping 

extension pipe

 (15) (pic.6) and the 

attachments (25, 26, 27) can be set on the 
flexible hose handle (14).

Carpet/floor brush (16) 

Set the switch on the brush to the desired 
position (depending on the type of the surface 
you wish to clean).

6

   ENGLISH         

VT-1832 R B.indd   6

VT-1832 R B.indd   6

05.08.2011   15:36:08

05.08.2011   15:36:08