Пылесос Rowenta RH8548R1 AIR FORCE - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
12
3 • Turning the vacuum cleaner on
Remove the charger cable from the vacuum
cleaner.
Hold the vacuum cleaner by the handle and
slide the power switch down, to one of the
two following positions (fig.6):
• “Floor”: for smooth floors (2.b)
In the «Floor» position, the electrobrush (11.a)
built into the Delta vacuum head, operates at
normal speed.
Note: regularly check that the wheels at the
back of the sucker attachment are clean.
• “Carpet / Booster” : for a better dust pick up
efficiency on all kinds of floors. (2.c)
In the «Carpet» position, the Booster light (3)
below the power switch comes on to indicate
that the electrobrush (11.a) is operating at high
speed.
Autonomy of your vacuum cleaner * depen-
ding on the position of use:
Position 1
« Floor »
Position 2
« Carpet/Booster »
18 Volts up to 40 MIN
up to 30 MIN
24 Volts up to 50 MIN
up to 40 MIN
USE OF THE ELECTROBRUSH
The Electrobrush is a motorised rotating
brush that ensures very effective cleaning.
It vacuums and cleans deep down. It has
bristles all along, enabling it to remove
threads and animal hair embedded in rugs
and carpets.
Note: If the sucker attachment adheres to the
surface too much, place the switch back to the
«Floor» position.
ATTENTION Do not vacuum large debris that
may block the brush and damage it.
Do not use the electro-brush on deep pile
carpets, animal fur and curtain fringes.
CLEANING THE ELECTROBRUSH
ATTENTION Always stop and unplug your va-
cuum cleaner before maintenance or cleaning.
Delicately cut the threads, hairs, animal fur,
etc. following the notch designed for this
purpose on the electrobrush (fig.7).
FOR YOUR SECURITY
• Do not touch the rotating parts without
having stopped and unplugged the vacuum
cleaner.
• Do not use the vacuum cleaner on a wet
surface.
• Never immerse your appliance in water.
TROUBLESHOOTING
The electrobrush is working less efficiently or
is making an abnormal noise
• The rotating brush or the hose are clogged:
stop the vacuum cleaner and clean them.
• The brush is worn: please contact an
Authorised Service Centre to have the brush
changed.
• The belt is worn: please contact an
Authorised Service Centre to have the belt
changed.
The electrobrush stops in the middle of
vacuuming
• The heat safety device has come on: stop
the vacuum cleaner by moving the switch to
the OFF position (2.a) and unplug it. Make
sure that nothing is impeding the rotation of
the brush, if so remove the obstacle and clean
the electrobrush (fig.7), then turn the vacuum
cleaner back on.
The electrobrush is difficult to move
• The suction power is too high: reduce the
suction power by moving the switch to the
«Floor» position (2b).
If the problem persists, take your vacuum
cleaner to the nearest Rowenta Approved
Service Centre.
See the list of Rowenta Authorised Service
Centres or contact the Rowenta Consumer
Service.
4 • Storage
After use, switch off your vacuum cleaner by
moving the switch to the OFF position (2a).
Your vacuum cleaner may then be put away
standing vertically wherever you want, in its
parking position.
To place the vacuum cleaner in its parking po-
sition: stand it vertically so as to lock it (Fig. 8)
To use it again: hold the handle and tilt it bac-
kwards to release it from the parking position
(Fig. 9)
EN
* Depending on model
