Пылесос ProfiCare PC-BS 3038 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
PC-BS3038_IM
27.03.19
32
Nozzle Attachments
• You can attach the nozzle attachments
both directly to the connector on the ap
-
pliance as well as to the already mounted
suction tube.
•
To detach the nozzle attachments, pull
them off while turning them slightly.
Floor Nozzle (12)
The floor nozzle is fitted with rollers for easier guiding.
You can clean smooth surfaces and carpets with the floor
nozzle.
• Adjust the brushes outwards or inwards using the lever
(11).
Best use of the appliance depends on the texture of the
floor covering. We recommend the following use:
• Use without brushes:
For vacuuming floor coverings with
a deep pile
• Use with brushes:
For vacuuming smooth floors and
carpets with a shallow pile
Hard Floor Brush
For gentle cleaning of hard surfaces such as parquet,
laminate, tiles, etc.
Crevice Nozzle
For vacuuming dirt from corners, joints and small gaps.
Brush Nozzle
For removing dirt gently from slits in upholstery and
mattresses. Also suitable for removing dust from sensitive
surfaces such as furniture or curtains.
Electrical Connection
• Before connecting the plug to the wall socket, check
whether the mains voltage is correct. Refer to the infor-
mation on the rating plate of the device.
•
Connect the device to a certified wall socket only.
Switching the Appliance On / Off
Turn the appliance on by using the on / off switch.
O
= Off
I
= Low suction power
II
=
High suction power
Assembly the Wall Holder
WARNING:
Make sure beforehand whether there are cables in the
wall which could be damaged!
1.
Measure the height for the wall holder. Hold the vacuum
cleaner against the wall when it is assembled with the
telescopic suction pipe and the floor nozzle.
2.
Hold the wall holder against the wall with the two drill
holes at the top and the bottom of the holder. Mark 2 drill
holes.
3. Drill the holes and insert the dowels into the wall.
4. Insert the screws through the holes of the wall holder.
Turn the screws with the wall holder into the dowels.
5.
Tighten the screws by hand.
Using the Appliance
1.
Unwind the power cord completely.
2.
Insert the mains plug into a correctly installed power
socket.
3.
Switch on the appliance with the on / off switch. Select a
desired speed setting (
I
or
II
).
4.
Adjust the floor nozzle with the lever depending on the
floor covering.
5.
Vacuum at a steady speed. There is no need to exert
pressure.
NOTE:
Pay attention to the range that can be covered with the
cable length!
End of Operation
1.
Turn the vacuum cleaner off by the on / off switch and re
-
move the plug from the socket.
2.
Let the device cool down completely.
3.
If you have already installed the wall
holder, hang up the vacuum cleaner.
4.
You can wind the power cord loosely
around the handle and the dust collector.
Maintenance
Emptying the Dust Collector
1. Disconnect the mains plug from the wall socket.
2.
If necessary, remove the suction tube or the nozzle
attachment from the appliance.
3.
Hold the appliance with the bottom plate of the dust col
-
lector over a dustbin.
4.
Empty the contents of the dust
collector. Press the (10) button to
open the bottom panel.
5.
Then close the base plate again.
The lock on the dust collector must
engage.
