Einhell PXC TC-VC 18/20 Li S-Solo (2347130) - Инструкция по эксплуатации - Страница 19

GB

- 19 -

Assembling the dirt bag (Fig. 9/14)

For vacuuming 

fi

 ne, dry dirt it is recommended 

that you 

fi

 t the dirt bag (14). Slip the dirt bag (14) 

over the vacuuming hole. The dirt bag (14) is sui-

table for dry-vacuuming only. The dirt bag makes 

it easier to dispose of the sucked-in dust.

5.3  Fitting the suction hose (Fig. 3, 10, 11)

Connect the suction hose (10) to the correspon-

ding connector on the wet and dry vacuum clea-

ner, depending on the application required.

Vacuuming

Connect the suction hose (10) to the suction hose 

connector (8)

Blowing

Connect the suction hose (10) to the blow con-

nector (9)

One or more of the elements which make up the 

3-part suction tube (11) can be attached to the 

suction hose (10) to extend it. The adapter (17) 

must be inserted between the suction tube (11) 

and the combination nozzle (12) or crevice nozzle 

(16).

5.4 Suction nozzles

Dual-purpose nozzle (Fig. 2)

The dual-purpose nozzle (12) is for vacuuming 

solids and liquids over medium to large areas.

Various attachments can be 

fi

 tted to the combi-

nation nozzle depending on what you sort of work 

you wish to carry out:

Crevice nozzle (Fig. 2)

The crevice nozzle (16) is designed for vacu-

uming solids and liquids in corners, edges and 

other areas that are di

ffi

  cult to access. 

Upholstery nozzle (Fig. 2)

The upholstery nozzle (25) is specially designed 

for vacuuming solids on upholstery and carpets.

5.5  Charging the battery (Fig. 12a)

1.  Take the battery pack out of the equipment. 

Do this by pressing the side pushlock buttons.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(21) into the socket outlet. The green LED will 

then begin to 

fl

 ash.

3.  Insert the battery pack (20) into the battery 

charger (21).

4.  In the section entitled „Charger indicator“ you 

will 

fi

 nd a table with an explanation of the LED 

indicator on the charger.

The battery pack can become a little warm during 

the charging. This is normal.

If the battery pack fails to charge, check:

• 

 whether there is voltage at the socket outlet

• 

 whether there is good contact at the charging 

contacts

If the battery pack still fails to charge, send

• 

 the charging unit

• 

 and the battery pack

to our customer service center.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly. 

You must recharge the battery pack when you 

notice that the performance of the device drops. 

Never allow the battery pack to become fully di-

scharged. This will cause it to develop a defect.

Fitting the battery (Fig. 8/20)

Open the battery cover (Fig. 8/19) Do this by 

swinging up the cover as shown in Fig. 8. Then 

insert the battery (Fig. 2/20) into the mount and 

push it forward until you hear the battery engage.

Battery capacity indicator (Fig. 12b/23)

Press the switch for the battery capacity indicator 

(a). The battery capacity indicator (Fig. 23) shows 

the charge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED 

fl

 ashes:

The battery is empty, recharge the battery.

All LEDs 

fl

 ash:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a 

defective battery pack.

Anl_TC_VC 1820 Li Kit_SPK9.indb   19

Anl_TC_VC 1820 Li Kit_SPK9.indb   19

20.11.2017   14:19:52

20.11.2017   14:19:52