Ardo PEO58 - Инструкция по эксплуатации - Страница 6

- 6 -

switched on to confirm.
- To switch the hotplate off press the relative on/off button.
NOTE:( During operation it will be possible to block / unblock the
control zone by depressing the key button for 3 seconds).

· Timer Area (Fig.5)
The surface has the possibility to set the timer simultaneously on
every cooking area. The timer is a function that allows setting a
time (from 1 to 99 minutes) to automatically switch off the selected
cooking area.
- Press the “Timer” button for 2 seconds: the display shows “00” in
the centre and it will show which element is active on the right and
left side.
- By continuing to press the “Timer” button the hotplate is selected
amongst those active.
- Press + or - to select the “Timer” value.
NOTE:
- If the “Timer” function has been imposed for more than one
cooking area, the “Timer Display” will show ever y 3 seconds the
remaining time for every programmed area.
- To cancel the “Timer” function, switch off the relative cooking
area.

· “MEMORY”  function
This function allows the programming and execution of one cook-
ing cycle on every warming element.

Note:
- One cycle at a time can be carried out in registration or in
execution.
- The variations of power level for the times inferior to 15 sec. are
not registered.
- One cooking cycle with a maximum duration of 10 hours and a
maximum of 10 variations of the power level can be memorised.

· Memorisation of a cooking cycle
- Press the “Memory” button and then select the desired hotplate
by means of the relative “ON/OFF” button.
- Press the buttons + or - until the desired power is selected.
- To terminate the memorisation cycle press once again the button
“ON/OFF”.

· Executing a cooking cycle
- To execute a cooking cycle already memorised, it is sufficient to
press the “ON/OFF” button of the interested cooking area followed
by the “Memory” button.

· Display
The cooking surface is supplied with a display that in nor mal func-
tion is a “WARCH” and can also carry out the “COUNTDOWN”
function when the surface is off.

· Regulation of the Watch
In the installation phase set the clock in the following way:
- Unblock the cooking surface by keeping the “key button” pressed
down for 3 seconds until the “indicator light button” is switched
off.
- Simultaneously press the buttons + and - under the display until
it begins flashing.
- Press + or - to set the desired time.
- Press the “Timer” button to confirm the selection.

· Countdown Function
- Unblock the cooking surface by keeping the “key button” pressed
down for 3 seconds until the “indicator light button” is switched off.
- Press the “Timer” button until the writing “00” appears on the
display.
- Press + or - to select the number of the minutes.
- Press the “Timer” button to confirm the selection.
At the end of the set time, an acoustic signal will be activated.

· Safety Systems
1.  In the instance where an object is placed over the controls, the
cook top will switch off and the auto-protection system will acti-
vate automatically, this occurs even in cases of liquid spills (wa-

ter, milk, etc.) over the controls zone.
2.  The commands keyboard has an internal temperature sensor
that, in the case that the internal temperature reaches 90° (abnor-
mal use conditions of the surface without pots) the surface will
automatically enter in an automatic system of temperature limita-
tion: switching itself off automatically.

· 

RESIDUAL HEAT

WARNING : when a cooking zone is switched off, the surface of
the cook top has a ver y high and dangerous temperature level.
The danger is highlighted by the fact that the “cooking zone dis-
play” will flicker until the temperature of the surface will not de-
crease to under 50°C.

· WARNINGS :
When the cook top is used with the power limitation (power level
2,4 / 3,4 / 4,4)) the following operation will guarantee the preset
maximum power level absorbed :

A) After having switched on a number of cooking zones to their
maximum power (position 9) the cook top may not accept the switch-
ing on of another “Cooking zone” and will emit an acoustic sound.
Or, turn on the next cooking zone (heating element) at a diverse
temperature than that desired.
B) When a number of cooking zones are switched on and there is
a desire to increase the temperature value, the cook top may not
accept the increase and will emit an acoustic sound.
C) After having switched on a number of cooking zones at an in-
termediate temperature value then when another element is
switched on then a few seconds delay may occur for the element
to light up.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR
EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE
WARNINGS.