Makita HS7611K - Инструкция по эксплуатации - Страница 8

8 ENGLISH

5. 

To check lower guard, open lower guard by hand, 

then release and watch guard closure. Also check 

to see that retracting handle does not touch 

tool housing.

 Leaving blade exposed is VERY 

DANGEROUS and can lead to serious personal injury.

Additional safety warnings

1. 

Use extra caution when cutting damp wood, pres-

sure treated lumber, or wood containing knots.

Maintain smooth advancement of tool without decrease 

in blade speed to avoid overheating the blade tips.

2. 

Do not attempt to remove cut material when 

blade is moving. Wait until blade stops before 

grasping cut material.

 Blades coast after turn off.

3. 

Avoid cutting nails. Inspect for and remove all 

nails from lumber before cutting.

4. 

Place the wider portion of the saw base on 

that part of the workpiece which is solidly 

supported, not on the section that will fall off 

when the cut is made. If the workpiece is short 

or small, clamp it down. DO NOT TRY TO HOLD 

SHORT PIECES BY HAND!

► 

Fig.5

5. 

Before setting the tool down after completing a 

cut, be sure that the guard has closed and the 

blade has come to a complete stop.

6. 

Never attempt to saw with the circular saw 

held upside down in a vise. This is extremely 

dangerous and can lead to serious accidents.

► 

Fig.6

7. 

Some material contains chemicals which may be 

toxic. Take caution to prevent dust inhalation and 

skin contact. Follow material supplier safety data.

8. 

Do not stop the blades by lateral pressure on 

the saw blade.

9. 

Do not use any abrasive wheels.

10. 

Only use the saw blade with the diameter that 

is marked on the tool or specified in the man

-

ual.

 Use of an incorrectly sized blade may affect 

the proper guarding of the blade or guard opera-

tion which could result in serious personal injury.

11. 

Keep blade sharp and clean.

 Gum and wood 

pitch hardened on blades slows saw and 

increases potential for kickback. Keep blade clean 

by first removing it from tool, then cleaning it with 

gum and pitch remover, hot water or kerosene. 

Never use gasoline.

12. 

Wear a dust mask and hearing protection when 

use the tool.

13. 

Always use the saw blade intended for cutting 

the material that you are going to cut.

14. 

Only use the saw blades that are marked with 

a speed equal or higher than the speed marked 

on the tool.

15. 

(For European countries only)  

Always use the blade which conforms to EN847-1.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity 

with product (gained from repeated use) replace 

strict adherence to safety rules for the subject 

product. MISUSE or failure to follow the safety 

rules stated in this instruction manual may cause 

serious personal injury.

FUNCTIONAL 

DESCRIPTION

CAUTION:

Always be sure that the tool is 

switched off and unplugged before adjusting or 

checking function on the tool.

Adjusting depth of cut

CAUTION:

After adjusting the depth of cut, 

always tighten the lever securely.

Loosen the lever on the depth guide and move the base 

up or down. At the desired depth of cut, secure the base 

by tightening the lever.

For cleaner, safer cuts, set cut depth so that no more 

than one blade tooth projects below workpiece. Using 

proper cut depth helps to reduce potential for danger-

ous KICKBACKS which can cause personal injury.

► 

Fig.7:

1.

 Depth gauge 

2.

 Lever 

3.

 Base

Bevel cutting

CAUTION:

After adjusting the bevel angle, 

always tighten the clamping screws securely.

Loosen the front and rear clamping screws. Set for 

the desired angle (0° - 45°) by tilting accordingly, then 

tighten the front and rear clamping screws securely.

► 

Fig.8:

1.

 Clamping screw

► 

Fig.9:

1.

 Clamping screw

Sighting

For straight cuts, align the 0° position on the front of the 

base with your cutting line. For 45° bevel cuts, align the 

45° position with it.

► 

Fig.10:

1.

 Cutting line (0° position) 

2.

 Cutting line 

(45° position)

► 

Fig.11:

1.

 Cutting line (0° position) 

2.

 Cutting line 

(45° position)

Switch action

WARNING:

Before plugging in the tool, 

always check to see that the switch trigger actu-

ates properly and returns to the "OFF" position 

when released.

► 

Fig.12:

1.

 Switch trigger 

2.

 Lock-off button

To prevent the switch trigger from being accidentally 

pulled, a lock-off button is provided. To start the tool, 

press the lock-off button and pull the switch trigger. 

Release the switch trigger to stop.