BORT BHK-160U - Инструкция по эксплуатации - Страница 7

7

build-up of debris)

•  Lower guard should be retracted manually only 
for special cuts such as plunge cuts and compound 
cuts; raise lower guard by retracting handle and as 
soon as blade enters the material, the lower guard 
must be released 

(for all other sawing, the lower guard 

should operate automatically)

•  Always observe that the lower guard is covering 
the blade before placing saw down on bench or 

fl

 oor 

(an unprotected, coasting blade will cause the 

saw to walk backwards, cutting whatever is in its path; 
be aware of the time it takes for the blade to stop after 
switch is released)
•  Avoid damage that can be caused by screws, nails 
and other elements in your workpiece; remove them 
before you start cutting
•  When you put away the tool, switch off the motor and 
ensure that all moving parts have come to a complete 
standstill
•  Use completely unrolled and safe extension cords 
with a capacity of 16Amps (U.K. 13Amps)
•  In case of jamming or electrical or mechanical 
malfunction, immediately switch off the tool and 
disconnect the plug
• The SBM Group can assure 

fl

 awless functioning of 

the tool only when original accessories are used
•  Use only accessories with an allowable speed 
matching at least the highest no-load speed of the tool
•  Never use the tool without the original protection 
guard system
•  This tool should not be used by people under the age 
of 16 years
•  The noise level when working can exceed 85 dB(A); 
wear ear protection
•  If the cord is damaged or cut through while working, 
do not touch the cord, but immediately disconnect the 
plug
•  Never use tool when cord is damaged; have it 
replaced by a quali

fi

 ed person

•  Always check that the supply voltage is the same as 
the voltage indicated on the nameplate of the tool (tools 
with a rating of 230V or 240V can also be connected to 
a 220V supply)
•  This tool is not suitable for wet cutting
•  After switching off your circular saw, never stop the 
rotation of the saw blade by a lateral force applied 
against it
•  Never use circular saw blades made of high speed 
steel (HSS)
•  Never use grinding/cutting discs with this tool

• Do not work materials containing asbestos 

(asbestos is considered carcinogenic)

•  Take protective measures when during work 
dust can develop that is harmful to one’s health, 
combustible or explosive 

(some dusts are considered 

carcinogenic); wear a dust mask and work with dust/
chip extraction when connectable
•  Do not attempt to cut extremely small workpieces
•  Remove all obstacles on top of as well as underneath 
the cutting path before you start cutting
•  Do not work overhead with the tool
•  Only use a saw table provided with a switch that 
prevents restarting of the motor after interruption of 
voltage

•  Only use a saw table provided with a kerf guide

• Always disconnect plug from power source 
before making any adjustment or changing any 
accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. 
ONLY):

•  Do not connect the blue (= neutral) or brown (= live) 
wire in the cord of this tool to the earth terminal of the 
plug
•  If for any reason the old plug is cut off the cord 
of this tool, it must be disposed of safely and not left 
unattended

Your machine is double insulated in accord-
ance with  EN 50144; therefore no earthwire 
is required.

MAINTENANCE

Make sure that the machine is not live when 
carrying out maintenance work on the motor. 

Regularly clean the machine housing with a soft cloth, 
preferably after each use. Keep the ventilation slots free 
from dust and dirt.If the dirt does not come off use a soft 
cloth moistened with soapy water. Never use solvents 
such as petrol, alcohol, ammonia water, etc. These sol-
vents may damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please 
contact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during 
transport, it is delivered in a sturdy packaging. Most of 
the packaging materials can be recycled. Take these 
materials to the appropriate recycling locations. Take 
your unwanted machines to your local SBM Group 
dealer. Here they will be disposed of in an environmen-
tally safe way.