Bosch GBH 36 V-LI - Инструкция по эксплуатации - Страница 21

 English | 

21

Bosch Power Tools

1 609 92A 0JA | (22.6.15)

Temperature Control Indicator

The red LED of the temperature control indicator 

19

 signals 

that the battery or the electronics of the power tool (when the 
battery is inserted) are not within the optimum temperature 
range. In this case, the power tool will not operate at full ca-
pacity.

Temperature control of the battery:
– The  red  LED 

19

 lights up continuously after inserting the 

battery into the charger: The battery is not within the 
charging temperature range between 0 ° C and 45 ° C and 
cannot be charged.

– The  red  LED 

19

 flashes when you press the 

21

 button or 

the On/Off switch 

10

 (with battery inserted): The battery 

is outside of the permitted operating temperature range.

– For battery temperatures over 70 ° C, the power tool 

switches off until the battery is in the optimal temperature 
range again.

Temperature control of the power tool electronics:
– The  red  LED 

19

 lights up continuously when pressing the 

On/Off switch 

10

: The temperature of the machine’s elec-

tronics is below 5 ° C or above 75 ° C.

– At a temperature above 90 ° C , the electronics of the pow-

er tool switch off until the temperature is within the allow-
able temperature range again.

Working Advice

Adjusting the Drilling Depth (see figure M)

The required drilling depth 

X

 can be set with the depth stop 

17

.

– Press the button for the depth stop adjustment 

15

 and in-

sert the depth stop into the auxiliary handle 

16

.

The knurled surface of the depth stop 

17

 must face down-

ward.

– Insert the SDS-plus drilling tool to the stop into the SDS-

plus tool holder 

3

. Otherwise, the movability of the SDS-

plus drilling tool can lead to incorrect adjustment of the 
drilling depth.

– Pull out the depth stop until the distance between the tip of 

the drill bit and the tip of the depth stop corresponds with 
the desired drilling depth 

X

.

Changing the Chiselling Position (Vario-Lock)

The chisel can be locked in 36 positions. In this manner, the 
optimum working position can be set for each application.

– Insert the chisel into the tool holder.
– Turn the mode selector switch 

13

 to the “Vario-Lock” posi-

tion (see “Setting the operating mode”, page 20).

– Turn the tool holder to the desired chiselling position.
– Turn the mode selector switch 

13

 to the “chiselling” posi-

tion. The tool holder is now locked.

– For chiselling, set the rotation direction to right rotation.

Inserting Screwdriver Bits (see figure N)



Apply the power tool to the screw/nut only when it is 
switched off. 

Rotating tool inserts can slip off.

To work with screwdriver bits, a universal bit holder 

31

 with 

SDS-plus shank (accessory) is required.

– Clean the shank end of the adapter shank and apply a light 

coat of grease.

– Insert the universal bit holder with a turning motion into 

the tool holder until it automatically locks.

– Check the locking effect by pulling the universal bit holder.
– Insert a screwdriver bit into the universal bit holder. Use 

only screwdriver bits that match the screw head.

– To remove the universal bit holder, pull the locking sleeve 

5

 toward the rear and remove the universal bit holder 

31

out of the tool holder.

Vibration Damper

The integrated vibration damper reduces occurring vibra-
tions.

The soft grip handle increases the safety against slipping off 
and thus provides for a better grip and handling of the power 
tool.

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.

Store the battery only within a temperature range between 
– 20 ° C and 50 ° C. As an example, do not leave the battery in 
the car in summer.

Occasionally clean the venting slots of the battery using a soft, 
clean and dry brush.

A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.

Observe the notes for disposal.

Maintenance and Service

Maintenance and Cleaning



Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport 
and storage, remove the battery from the power tool. 

There is danger of injury when unintentionally actuating 
the On/Off switch.



For safe and proper working, always keep the machine 
and ventilation slots clean.



A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by 
an after-sales service.

– Clean the tool holder 

3

 each time after using.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare 
parts. Exploded views and information on spare parts can al-
so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions 
concerning our products and their accessories.

OBJ_BUCH-283-012.book  Page 21  Monday, June 22, 2015  10:28 AM