Bosch GBH 2-24 D - Инструкция по эксплуатации - Страница 10

10

 | English 

1 619 92A 06J | (2.12.13)

Bosch Power Tools

Hammer Safety Warnings



Wear ear protectors. 

Exposure to noise can cause hear-

ing loss.



Use auxiliary handle(s), if supplied with the tool. 

Loss 

of control can cause personal injury.



Hold the tool by the insulated gripping surfaces when 
performing operations where the application tool or 
the screw could contact hidden wiring or its own power 
cord. 

Contact with a “live” wire will also make exposed 

metal parts of the power tool “live” and shock the operator.

Products sold in GB only

: Your product is fitted with a 

BS 1363/A approved electric plug with internal fuse (ASTA 
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be 
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should 
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible 
shock hazard and should never be inserted into a mains sock-
et elsewhere.

Products sold in AUS and NZ only

: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

Additional Safety and Working In-
structions



Observe the mains voltage! 

The voltage of the power 

source must correspond with the data on the type plate of 
the machine.



Use appropriate detectors to determine if utility lines 
are hidden in the work area or call the local utility compa-
ny for assistance. 

Contact with electric lines can lead to fire 

and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage.



Firmly tighten the auxiliary handle, hold the machine 
firmly with both hands while working and keep proper 
footing and balance at all times. 

The machine is securely 

guided with both hands.



Secure the workpiece. 

A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.



To save energy, only switch the power tool on when using it.



For drilling without impact in wood, metal, ceramic and 
plastic as well as for screwdriving, tools without SDS-plus 
are used (e. g., drills with cylindrical shank). For these 
tools, a keyless chuck or a key type drill chuck are re-
quired.



The quick change chuck is automatically locked. Check the 
locking effect by pulling the quick change chuck.



Inserting SDS-plus Drilling Tools: 

Check the latching by 

pulling the tool.



Replace a damaged dust protection cap immediately. 

The dust protection cap largely prevents the penetration of 
drilling dust into the tool holder during operation. When in-
serting the tool, pay attention that the dust protection cap 
is not damaged.



Dusts from materials such as lead-containing coatings, 
some wood types, minerals and metal can be harmful to 
one’s health and cause allergic reactions, lead to res-
piratory infections and/or cancer.

 Materials containing 

asbestos may only be worked by specialists.

–

As far as possible, use a dust extraction system suita-
ble for the material.

–

Provide for good ventilation of the working place.

–

It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the 
materials to be worked.



Prevent dust accumulation at the workplace. 

Dusts can 

easily ignite.



If the application tool should become blocked, switch 
the machine off. Loosen the application tool.



Before switching on the power tool, make sure that the 
application tool moves freely. 

When switching on with a 

blocked drilling tool, high torque reaction can occur.



Always wait until the machine has come to a complete 
stop before placing it down. 

The tool insert can jam and 

lead to loss of control over the power tool.

Symbols

The following symbols are important for reading and under-
standing the operating instructions. Please take note of the 
symbols and their meaning. The correct interpretation of the 
symbols will help you to use the machine in a better and safer 
manner.

Symbol

Meaning

GBH 2-24 D
GBH 2-24 DF:
Rotary Hammer

Grey-marked area: Handle (insulated 
gripping surface)

Article number

Read all safety warnings and all instruc-
tions

Before any work on the machine itself, 
pull the mains plug from the socket out-
let

Wear protective gloves

Always wear ear protection.

OBJ_BUCH-1426-004.book  Page 10  Monday, December 2, 2013  12:45 PM