Bosch GBH 180-LI Professional - Инструкция по эксплуатации - Страница 10

10

 | English 

1 609 92A 34V | (3.11.16)

Bosch Power Tools



Disconnect the plug from the power source and/or the 
battery pack from the power tool before making any 
adjustments, changing accessories, or storing power 
tools. 

Such preventive safety measures reduce the risk of 

starting the power tool accidentally.



Store idle power tools out of the reach of children and 
do not allow persons unfamiliar with the power tool or 
these instructions to operate the power tool. 

Power 

tools are dangerous in the hands of untrained users.



Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other 
condition that may affect the power tool’s operation. If 
damaged, have the power tool repaired before use. 

Many 

accidents are caused by poorly maintained power tools.



Keep cutting tools sharp and clean. 

Properly maintained 

cutting tools with sharp cutting edges are less likely to bind 
and are easier to control.



Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account 
the working conditions and the work to be performed. 

Use of the power tool for operations different from those 
intended could result in a hazardous situation.

Battery tool use and care



Recharge only with the charger specified by the manu-
facturer. 

A charger that is suitable for one type of battery 

pack may create a risk of fire when used with another bat-
tery pack.



Use power tools only with specifically designated bat-
tery packs. 

Use of any other battery packs may create a 

risk of injury and fire.



When battery pack is not in use, keep it away from oth-
er metal objects, like paper clips, coins, keys, nails, 
screws or other small metal objects, that can make a 
connection from one terminal to another. 

Shorting the 

battery terminals together may cause burns or a fire.



Under abusive conditions, liquid may be ejected from 
the battery; avoid contact. If contact accidentally oc-
curs, flush with water. If liquid contacts eyes, addition-
ally seek medical help. 

Liquid ejected from the battery 

may cause irritation or burns.

Service



Have your power tool serviced by a qualified repair per-
son using only identical replacement parts. 

This will en-

sure that the safety of the power tool is maintained.

Hammer Safety Warnings



Wear ear protectors. 

Exposure to noise can cause hear-

ing loss.



Use auxiliary handle(s), if supplied with the tool. 

Loss 

of control can cause personal injury.



Hold the tool by the insulated gripping surfaces when 
performing operations where the application tool or 
the screw could contact hidden wiring or its own power 
cord. 

Contact with a “live” wire will also make exposed 

metal parts of the power tool “live” and shock the operator.

Additional Safety and Working In-
structions



When transporting and storing, set the rotational di-
rection switch to the centre position. 

Danger of injury 

when accidentally actuating the On/Off switch.



Use appropriate detectors to determine if utility lines 
are hidden in the work area or call the local utility com-
pany for assistance. 

Contact with electric lines can lead 

to fire and electric shock. Damaging a gas line can lead to 
explosion. Penetrating a water line causes property dam-
age.



Firmly tighten the auxiliary handle, hold the machine 
firmly with both hands while working and keep proper 
footing and balance at all times. 

The power tool is guided 

more secure with both hands.



Secure the workpiece. 

A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.



For drilling without impact in wood, metal, ceramic and 
plastic as well as for screwdriving, tools without SDS-plus 
are used (e. g., drill bits with cylindrical shank). For these 
tools, a keyless chuck or a key type drill chuck are re-
quired.



The quick change chuck is automatically locked. Check the 
locking effect by pulling the quick change chuck.



Inserting SDS-plus Drilling Tools: 

Check the latching by 

pulling the tool.



Replace a damaged dust protection cap immediately. 

The dust protection cap largely prevents the penetration of 
drilling dust into the tool holder during operation. When in-
serting the tool, pay attention that the dust protection cap 
is not damaged.



Dust from materials such as lead-containing coatings, 
some wood types, minerals and metal can be harmful to 
one’s health and cause allergic reactions, lead to res-
piratory infections and/or cancer.

 Materials containing 

asbestos may only be worked by specialists.

–

As far as possible, use a dust extraction system suitable 
for the material.

–

Provide for good ventilation of the working place.

–

It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the 
materials to be worked.



Prevent dust accumulation at the workplace. 

Dust can 

easily ignite.



To save energy, only switch the power tool on when using it.



Apply the power tool to the screw/nut only when it is 
switched off. 

Rotating tool inserts can slip off.



If the application tool should become blocked, switch 
the machine off. Loosen the application tool.



Before switching on the power tool, make sure that the 
application tool moves freely. 

When switching on with a 

blocked drilling tool, high torque reaction can occur.



Always wait until the machine has come to a complete 
stop before placing it down. 

The tool insert can jam and 

lead to loss of control over the power tool.

OBJ_BUCH-2932-001.book  Page 10  Thursday, November 3, 2016  3:00 PM