Bort BHD-1500-MAX - Инструкция по эксплуатации - Страница 8

8

or entangled cords increase the risk of electric shock .

•  When operating a power tool outdoors, use an extension 

cord suitable for outdoor use . Use of a cord suitable for 

outdoor use reduces the risk of electric shock .

•  If operating a power tool in a damp location is unavoida-

ble, use a residual current device (RCD) protected supply . 

Use of an RCD reduces the risk of electric shock .

Personal safety

•  Stay alert, watch what you are doing and use common 

sense when operating a power tool . Do not use a power 

tool while you are tired or under the influence of drugs, 

alcohol or medication . A moment of inattention while op-

erating power tools may result in serious personal injury .

•  Use personal protective equipment . Always wear eye 

protection . Protective equipment such as dust mask, 

non-skid safety shoes, hard hat, or hearing protection 

used for appropriate conditions will reduce personal in-

juries .

•  Prevent unintentional starting . Ensure the switch is in 

the off-position before connecting to power source and/

or battery pack, picking up or carrying the tool . Carrying 

power tools with your finger on the switch or energising 

power tools that have the switch on invites accidents .

•  Remove any adjusting key or wrench before turning the 

power tool on . A wrench or a key left attached to a rotat-

ing part of the power tool may result in personal injury .

•  Do not overreach . Keep proper footing and balance at 

all times . This enables better control of the power tool in 

unexpected situations .

•  Dress properly . Do not wear loose clothing or jewellery . 

Keep your hair, clothing and gloves away from moving 

parts . Loose clothes, jewellery or long hair can be caught 

in moving parts .

•  If devices are provided for the connection of dust extrac-

tion and collection facilities, ensure these are connected 

and properly used . Use of dust collection can reduce 

dust-related hazards .

Power tool use and care

•  Do not force the power tool . Use the correct power tool 

for your application . The correct power tool will do the 

job better and safer at the rate for which it was designed .

•  Do not use the power tool if the switch does not turn it 

on and off . Any power tool that cannot be controlled with 

the switch is dangerous and must be repaired .

•  Disconnect the plug from the power source and/or the 

battery pack from the power tool before making any ad-

justments, changing accessories, or storing power tools . 

Such preventive safety measures reduce the risk of start-

ing the power tool accidentally .

•  Store idle power tools out of the reach of children and do 

not allow persons unfamiliar with the power tool or these 

instructions to operate the power tool . Power tools are 

dangerous in the hands of untrained users .

•  Maintain power tools . Check for misalignment or bind-

ing of moving parts, breakage of parts and any other 

condition that may affect the power tool’s operation . If 

damaged, have the power tool repaired before use . Many 

accidents are caused by poorly maintained power tools .

•  Keep cutting tools sharp and clean . Properly main-

tained cutting tools with sharp cutting edges are less 

likely to bind and are easier to control .

•  Use the power tool, accessories and tool bits etc . in ac-

cordance with these instructions, taking into account the 

working conditions and the work to be performed . Use 

of the power tool for operations different from those in-

tended could result in a hazardous situation .

Service

Have your power tool serviced by a qualified repair person 

using only identical replacement parts . This will ensure that 

the safety of the power tool is maintained .

HAMMER SAFETY WARNINGS

•  Observe the mains voltage! The voltage of the power 

source must correspond with the data on the type plate 

of the machine . Power tools marked with 230/240 V can 

also be operated with 220 V .

•  Use appropriate detectors to determine if utility lines are 

hidden in the work area or call the local utility company 

for assistance . Contact with electric lines can lead to fire 

and electric shock . Damaging a gas line can lead to ex-

plosion . Penetrating a water line causes property dam-

age .

•  Firmly tighten the auxiliary handle, hold the machine 

firmly with both hands while working and keep proper 

footing and balance at all times . The machine is securely 

guided with both hands .

•  Secure the workpiece . A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand .

•  For drilling without impact in wood, metal, ceramic and 

plastic as well as for screwdriving, tools without SDS 

Max are used (e .g ., drill bits with cylindrical shank) . For 

these tools, a keyless chuck or a key type drill chuck are 

required .

•  The quick change chuck is automatically locked . Check 

the locking effect by pulling the quick change chuck .

•  Inserting SDS Max Drilling Tools: Check the latching by 

pulling the tool .

•  Replace a damaged dust protection cap immediately . 

The dust protection cap largely prevents the penetra-

tion of drilling dust into the tool holder during operation . 

When inserting the tool, pay attention that the dust pro-

tection cap is not damaged .

•  To save energy, only switch the power tool on when us-

ing it .

•  Dusts from materials such as lead-containing coatings, 

some wood types, minerals and metal can be harmful to 

one’s health and cause allergic reactions, lead to respira-

tory infections and/or cancer . Materials containing asbes-

tos may only be worked by specialists .

•  As far as possible, use a dust extraction system suitable 

for the material .

•  Provide for good ventilation of the working place .

•  It is recommended to wear a P2 filter-class respirator .

•  Observe the relevant regulations in your country for the 

materials to be worked .

•  Prevent dust accumulation at the workplace . Dusts can 

easily ignite .

•  If the application tool should become blocked, switch 

the machine off . Loosen the application tool .

•  Before switching on the power tool, make sure that the 

application tool moves freely . When switching on with a 

blocked drilling tool, high torque reaction can occur .

•  Always wait until the machine has come to a complete