BRAYER BR4122 - Инструкция по эксплуатации - Страница 5

8

9

EN

EN

• 

Do not fill the tank (1) with carbonated water, 

perfume additives, vinegar, chemical agents, etc.

•  Install the water tank (1) back to its place and make 

sure that the tank (1) is fixed properly. 

ATTENTION!
Do not plug the garment steamer in if the water tank 

(1) is empty.

• 

Place the garment steamer on the base (10) on a flat 

and steady surface.

•  Connect the power plug (9) to the mains socket, the 

indicator (6) will light up. Wait for some time (from 

3 to 5 minutes) necessary for normal generation of 

steam.

•  Take the garment steamer by the handle (8) on the 

same level with the steam supply on button (4) (pic. 

3).

•  To switch the steam supply on, press and hold down 

the button (4).

• 

To switch the steam supply off release the button (4).

•  Before general use of the garment steamer clean the 

steam chamber. To do this, direct the outgoing steam 

to a piece of cloth, for instance, try to smooth out a 

kitchen towel.

•  If during the operation the water tank (1) becomes 

empty, switch the garment steamer off before 

removing the tank (1) and refilling it with water. To do 

this, disconnect the power plug (9) from the mains 

socket.

•  After the unit operation, remove the power plug (9) 

from the mains socket and let the garment steamer 

cool down.

Note:

 when switching the unit on for the first time, 

foreign smell can appear. It is normal.

USING THE BRUSH ATTACHMENT
ATTENTION!
Before installing the brush attachment (11) and 

removing the tank (1), make sure that the power 

plug (9) is not inserted into the mains socket.

•  Install the brush attachment (11) on the garment 

steamer (pic. 4).

•  Press the buttons (3) on both sides of the water tank 

and remove the water tank (1) (pic. 1). 

•  Open the water inlet lid (2). Fill the water tank (1) with 

water non exceeding the MAX mark and close the 

water inlet lid (2) tightly (pic. 2). 

• 

Do not fill the tank (1) with carbonated water, 

perfume additives, vinegar, chemical agents, etc.

•  Install the water tank (1) back to its place and make 

sure that the tank (1) is fixed properly. 

• 

Place the garment steamer on the base (10) on a flat 

and steady surface.

•  Connect the power plug (9) to the mains socket, the 

indicator (6) will light up. Wait for some time (from 

3 to 5 minutes) necessary for normal generation of 

steam.

•  Take the garment steamer by the handle (8) on the 

same level with the steam supply on button (4) (pic. 

3).

•  Hang the clothes on a hanger.

Note:

 never steam clothes on a person as the outgoing 

steam temperature is very high, use a hanger only.
•  To switch the steam supply on, press and hold down 

the button (4).

• 

To switch the steam supply off release the button (4).

•  Slowly move the brush attachment (11) along the 

fabric, smooth out the fabric with your free hand.

Notes:

- during operation, hold the garment steamer vertically 

and do not turn it over;
- during the garment steamer operation the upper part 

of the body (7) becomes very hot. Be careful and do not 

touch hot parts of the unit body (7) and the operating 

surface (5);
- after steaming the clothes may need some time to dry, 

leave them on the hanger.
•  After the unit operation, remove the power plug (9) 

from the mains socket and let the garment steamer 

cool down.

•  Detach the brush attachment (pic. 5).

•  Remove the water tank (1), open the lid (2) and pour 

out the remaining water, install the water tank (1) 

back to its place.

OVERHEATING PROTECTION

•  If you accidentally switch the garment steamer on 

without water or the water level appears to be below 

the minimal mark, the automatic thermal switch will 

be on and the garment steamer will be switched off 

and the indicator (6) will go out.

•  In this case disconnect the power plug (9) from the 

mains sockets and let the garment steamer cool 

down for 15-20 minutes. Then fill the water tank (1) 

with water and insert the power plug (9) to the mains 

socket, the garment steamer will operate in normal 

mode.

CLEANING AND  CARE

•  Disconnect the power plug (9) from the mains socket 

and wait until the garment steamer cools down 

completely.

•  Remove the water tank (1), open the lid (2) and pour 

out the remaining water, install the water tank (1) 

back to its place.

•  Clean the garment steamer body (7) and the 

operating surface with the steam release openings 

(5) with a slightly damp cloth, and then wipe dry.

•  You can remove the mineral deposit from the 

operating surface (5) with a cloth soaked in vinegar-

water solution.

•  Remove the brush attachment (11) and wash it under 

a water jet.