Timberk TOR 51.2009 BTM - Инструкция по эксплуатации - Страница 5

www.timberk.com • electric oil filled radiator

5

IMPORTANT! 

1. Switch on and operate the radiator only when upright (with 

wheels below and control elements above). Any other position 

may cause a dangerous situation and result in failure of the oil-

filled radiator or damage of property and the manufacturer will 

consider this as a non-warranty case.
2. Do not switch the radiator on, if roller wheels are not installed.

1. Read section «Important precautions» carefully unless you already did it.
2. Connect the unit’s power cord to an electric outlet, observing all of the 

abovementioned precautions. Remember that you can connect the unit to 

electric mains only if the rotating power regulator is in OFF position (switched 

off), i.e. the knob is rotated against the stop counterclockwise.
3. It is also preferable to turn the temperature regulating knob against the stop 

counterclockwise. Then you can connect the unit to electric mains.
4. Set the unit’s power regulator (knob) to position I, II or III (corresponds to low, 

normal and maximum power of unit’s operation). Remember that the higher the 

power you choose, the faster the unit heats the air. But at a low power you save 

electric power and reduce the load on your electric mains.
5. After you chose the desired operating power in accordance with your 

individual preferences, you have to choose the desired heating temperature.
Turning the thermostat knob clockwise (from MIN position towards MAX 

position), you thus adjust the temperature mode you need. Since the moment 

you choose the temperature mode (provided one or another power mode is 

activated see item 4) the oil filled radiator will start to operate.
6. During the first minutes of radiator’s operation you may fell a slight smell of 

burning. It may be caused by dust on the unit; it will soon disappear. If necessary, 

you can perform a preliminary preventive cleaning of the unit, following rules, set 

forth in this manual and observing «Important precautions».
7. When the room temperature will reach the desired level, you should slowly 

turn the temperature regulator’s knob counterclockwise (towards MIN). You will 

hear a click of the thermostat turning off, and the light on the control panel will 

go out. Now the room temperature will be maintained at the chosen level.

7. UNIT OPERATION RULES AND PROCEDURE

IMPORTANT! 

For the unit to operate normally, the level of voltage in 

electric mains must be sufficient in strict compliance 

with the technical parameters indicated on the unit. 

Carefully study the technical label, as well as all labels 

with special warnings, attached to the unit’s surface.

1. Remember that you must clean the unit regularly to remove dust from the 

surface of heating sections. Dust and dirt on the unit’s surface have a negative 

effect on the unit’s operational efficiency, in some cases a smell of burning dust 

can cause a headache and nausea, as well as other negative health effects. 

Also a dirty unit cannot operate 100% effectively, temperature parameters of 

the room heating can be disrupted.
2. Prior to preventive cleaning of the unit, you must switch off the unit, unplug 

it from electric mains (see «Important precautions») and let the unit cool down.
3. Clean the unit’s sections and other surfaces with a soft, slightly damp duster/

cloth. The cloth must not leave fluff on the unit’s surface.
4. It is not recommended to use detergents, including materials containing 

abrasive elements.
5. During cleaning, please, do not damage the unit’s surface by sharp objects 

(hard sponge, polishing paper, etc). Scratches on the painted surface can result 

in rusting.
Switch on and use the unit again only having carried out all «Important 

precautions»; also make sure that the unit’s surface is absolutely dry.

8. CLEANING AND MAINTENANCE OF THE UNIT

8. If you need to reduce the room temperature, turn the thermostat knob 

counterclockwise. Also you can lower the unit’s operating power (I or II).
9. If you need to raise the room temperature, turn the thermostat knob 

clockwise (maximum possible position MAX indicator). Also you can raise the 

unit’s operating power (II or III).