Netgear GS316PP 16xGE PoE - Инструкция по эксплуатации

© NETGEAR, Inc., NETGEAR and the NETGEAR Logo

are trademarks of NETGEAR, Inc. Any non‑NETGEAR

trademarks are used for reference purposes only.

Installation Guide

Register with the NETGEAR Insight app

1. Search for

NETGEAR Insight

and download the latest app.

2. Set up a NETGEAR account if you do not have one.
3. Tap the menu in the upper-left corner.
4. Tap

REGISTER ANY NETGEAR DEVICE

.

5. Enter the serial number located on the bottom of the switch, or use the

camera on your mobile device to scan the serial number bar code.

6. Tap

GO

.

The switch is registered and added to your account. You can now view the
switch in the NETGEAR Insight app.

Note:

Because this is an unmanaged switch, you cannot configure or manage it

in NETGEAR Insight.

Connect the switch

1. Connect network devices to the ports on the switch.
2. Connect an RJ-45 port on the switch to a network.

Note:

In a small office or home office network, connect the switch to the LAN

port of a router that, in turn, is connected to an Internet modem.

3. Power on the switch.

PoE considerations

The switch prioritizes the PoE+ power that it supplies in ascending port order
(from port 1 to port 16). If the aggregate power requirements of all attached
power devices (PD) exceed the power budget of the switch, the PD on the
highest-numbered port is disabled to make sure that the PDs that are connected

to the higher-priority, lower-numbered ports are supported first.

The following tables describe the power adapter models that are compatible with
the GS316P and GS316PP switches and their PoE classes and switch allocations:

Note:

The listed total power budget is the maximum power limit for the

switch. Many PDs require less than maximum power, so the aggregate power
requirements are lower than the maximum, allowing all sixteen PoE ports to be
active simultaneously.

Power adapters and total power budgets for the GS316P and GS316PP:

Power adapter model

Power adapter

Total power budget

EPS90W

90W

76W

EPS130W

130W

115W

EPS200W

200W

183W

PoE classes and switch allocations:

Device
class

Standard

Class
description

Minimum power
allocated to the
powered device

Range of power
delivered to the
powered device

0

PoE and PoE+

Default power
(full)

0.44W

0.44W–12.95W

Device
class

Standard

Class
description

Minimum power
allocated to the
powered device

Range of power
delivered to the
powered device

1

PoE and PoE+

Very low
power

4.0W

0.44W–3.84W

2

PoE and PoE+

Low power

7.0W

3.84W–6.49W

3

PoE and PoE+

Mid power

15.4W

6.49W–12.95W

4

PoE+ only

High power

30.0W

12.95W–25.5W

PoE troubleshooting

Here are some tips for correcting PoE problems that might occur:
•

Make sure that the PoE Max LED is off. If the PoE Max LED is solid yellow,

disconnect one or more PoE devices to prevent PoE oversubscription. Start by
disconnecting the device from the highest-numbered port.

• Make sure that the Ethernet cables are plugged in correctly. For each

powered device (PD) that is connected to the switch, the corresponding right

port LED on the switch lights solid green. If the right port LED lights solid

yellow, a PoE fault occurred and PoE halted because of one of the conditions
that are listed in the following table.

PoE Fault Condition

Possible Solution

A PoE-related short circuit occurred on the
port.

The problem is most likely with the attached
PD. Check the condition of the PD or restart the
PD by disconnecting and reconnecting the PD.

The PoE power demand of the PD exceeded
the maximum level that the switch permits,
which is 30.9W.

The PoE current on the port exceeded the

classification limit of the PD.

The PoE voltage of the port is outside the
range that the switch permits.

Restart the switch to see if the condition
resolves itself.

16-port Gigabit Ethernet Unmanaged
High-Power PoE+ Switch with FlexPoE

Models GS316P and GS316PP

Package contents

• Switch
• Power cord (varies by region)
• Power Adapter (130W for GS316P/200W for GS316PP)
• Wall installation kit

• Rubber feet
• Mounting ties (for power adapter)
• Installation guide

December 2019

Sample connections

PoE VoIP
Phone

Wave 2
Wireless AP

PoE+ securit y
camera

Router

GS316PP

Internet

Laptop

Smar t
phone

Internet

PoE+