VITEK VT-3510 PK - Инструкция по эксплуатации - Страница 3

ENGLISH

3

CLOCK RADIO

CONTROLS AND FUNCTIONS

1.  Power cord
2.  FM antenna
3.  SNOOZE button
4.  Battery compartment
5.  RUN/ALM/TIME Clock function selector
6.  ON/AUTO/OFF Function selector
7.  Lighted display
8.  Rotating function dial
9.  SLEEP button
10. Radio frequency tuning knob
11. AM/FM Band selector
12. VOLUME/BUZZER knob
13. Projector
14. Projector On/Off button
15. Minute setting button for projector
16. Hour setting button for projector
17. Projector focus control
18. Time setting button for projector

POWER

1.  Connect the power cord to the outlet. 

Make sure that the voltage indicated on the 
device matches the voltage in your home.

2.  Place one 9 V battery (not included) into 

the battery compartment (4). The bat-
tery maintains the clock in case of power 
failure. In such cases, the display will not 
work, but the time is being maintained.

RADIO

1.  Set the ON/AUTO/OFF (6) selector to the 

ON position.

2.  Set the desired band using the band selec-

tor (11).

3.  Tune to the desired radio station using the 

tuning knob (10).

4.  Adjust the volume by turning the knob 

(12).

5.  Extend the antenna wire (2) fully for best 

reception of FM-band signals.

6.  Set the selector (6) to the OFF position to 

turn the radio off.

SET TING THE CURRENT TIME

In order to set the current time, move the 
RUN/ALM/TIME (5) selector to the TIME po-
sition and turn the dial (8) to the left (to set 

the minutes) or to the right (to set the hours). 
When the time has been set, move the RUN/
ALM/TIME (5) selector back to RUN. The two 
blinking dots on the display (7) should stop 
blinking.

SET TING THE CURRENT TIME FOR THE 
PROJECTOR

Attention! The current time shown on the dis-
play and that projected by the projector must 
be set separately.

Projector:

Set the projector selector (14) to the ON posi-
tion. Press and hold the T button (18); press 
the H (16) button to set the hours and the M 
(15) button to set the minutes. Switch the pro-
jector selector (14) to the OFF position to turn 
the projector off.

Note: The time displayed by the projector on 
the wall or ceiling can be easily seen in a dark 
room. The maximum projection distance is 
0.6 – 2.7 m. Use the focus control dial (17) 
to adjust the brightness and focus of the pro-
jected image.

SET TING THE ALARM TIME

In order to set the current time, move the 
RUN/ALM/TIME (5) selector to the ALARM 
position and turn the dial (8) to the left (to set 
the minutes) or to the right (to set the hours). 
When the time has been set, move the RUN/
ALM/TIME (5) selector back to RUN. The two 
blinking dots on the display (7) should stop 
blinking.

AT TENTION!

Do not rotate the dial to fast because the clock 
cannot react at high speeds.

WAKING UP TO MUSIC

1.  Set the ON/AUTO/OFF (6) selector to the 

AUTO position.

2.  Tune to the desired station by rotating the 

frequency-tuning knob (10).

3.   Set the desired volume by rotating the knob (12).
4.  The radio will turn on at the pre-set time.
5.  Set the function selector (1) to the OFF po-

sition to turn off the alarm.

3510_2_IM.indd   3

3510_2_IM.indd   3

19.09.2011   9:19:05

19.09.2011   9:19:05