Aurora ADP 900 H - Инструкция по эксплуатации - Страница 7

7

GB

Cordless drill/driver

INTENDED USE
•  This tool is intended for drilling in wood, metal, ceramic and 

plastic; tools with electronic speed control and left/right ro-
tation are also suitable for screwdriving and thread cutting

TECHNICAL SPECIFICATIONS  

 1 

PRODUCT ELEMENTS  

 2 

1  Switch for on/off and speed control
2  Switch for changing direction of rotation
3 Keyless chuck
4  Ring for torque control

SAFETY

WARNING! Read all instructions. Failure to follow all instruc-
tions listed below may result in electric shock, 

fi

 re and/or seri-

ous injury. 

•  Ensure the switch is in the off position before inserting bat-

tery pack. Inserting the battery pack into power tools that 
have the switch on invites accidents.

•  Recharge only with the charger speci

fi

 ed by the manufac-

turer. A charger that is suitable for one type of battery pack 
may create a risk of 

fi

 re when used with another battery 

pack.

•  Use power tools only with speci

fi

 cally designated battery 

packs. Use of any other battery packs may create a risk of 
injury and 

fi

 re.

•  Avoid damage that can be caused by screws, nails and 

other elements in your workpiece; remove them before you 
start working

•  Always check that the supply voltage is the same as the 

voltage indicated on the nameplate of the charger (charg-
ers with a rating of 230V or 240V can also be connected to 
a 220V supply)

•  In case of electrical or mechanical malfunction, immediate-

ly switch off the tool or unplug charger from power source

•  SBM Group can assure 

fl

 awless functioning of the tool only 

when original accessories are used

•  Use only accessories with an allowable speed matching at 

least the highest no-load speed of the tool

•  This tool should not be used by people under the age of 16 

years

•  Be careful not to drill or drive into areas where electrical 

wires may be contacted

•  Ensure that switch 

 is in the middle (locking) position 

before making any adjustments or changing accessories 
as well as when carrying or storing the tool

•  Do not touch the contacts in the charger
•  Do not expose tool/charger/battery to rain
•  Never charge battery outdoors
•  Store tool/charger/battery in locations where temperature 

will not exceed 40 °C or drop below 0 °C

•  Batteries will explode in 

fi

 re, so do not burn battery for any 

reason

•  When damaged, and under extreme usage and tempera-

ture conditions, batteries may start to leak

-  if liquid comes into contact with the skin, wash quickly with 

soap and water, then with lemon juice or vinegar

-  if liquid gets into the eyes, 

fl

 ush eyes with clean water for 

a minimum of 10 minutes and seek immediately medical 
attention

•  When battery is not in tool or charger, it should be kept 

away from metal objects such as nails, screws, keys etc. to 
prevent short-circuit

•  Do not use charger when damaged; take it to one of the of-

fi

 cially registered SBM Group Service Stations for a safety 

check

•  Do not use battery when damaged; it should be replaced 

immediately

•  Do not disassemble charger or battery
•  Do not attempt to recharge non-rechargeable batteries with 

the charger

•  Normally when starting to charge the discharged battery, 

red and green LEDs of the battery charger are on. When 
the battery is fully charged only green LED is on. If no LEDs 
are on while the charger is on, do not use the battery and 
the charger and take them to the service center. 

•  When using your tool continuously, the batteries in your 

battery pack will become hot. You should let a hot battery 
pack cool down for approximately 30 minutes before at-
tempting to recharge.

•  In case of long storage, store the battery in fully charged 

condition. 

  WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
•  Do not connect the blue (= neutral) or brown (= live) wire in 

the cord of the charger to the earth terminal of the plug

•  If for any reason the old plug is cut off the cord of the charg-

er, it must be disposed of safely and not left unattended

To ensure longer service life and proper perfor-
mance of the battery, take the following actions 
when you start using new battery: 

1.  Use the new battery, without recharging it, till its complete 

discharge. 

2.  Then charge the battery for 3-5 hours.
3. Repeat abovementioned actions (1 and 2) 3-5 times to 

reach the nominal battery capacity.

MAINTENANCE

Make sure that the machine is not live when carry-
ing out maintenance work on the motor. 

Regularly clean the machine housing with a soft cloth, prefer-
ably after each use. Keep the ventilation slots free from dust 
and dirt.If the dirt does not come off use a soft cloth moistened 
with soapy water. Never use solvents such as petrol, alcohol, 
ammonia water, etc. These solvents may damage the plastic 
parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please contact 
your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during transport, 
it is delivered in a sturdy packaging. Most of the packaging 
materials can be recycled. Take these materials to the appro-
priate recycling locations. Take your unwanted machines to 
your local SBM Group dealer. Here they will be disposed of in 
an environmentally safe way.
Li-Ion batteries can be recycled. Deliver them to a disposal 
site for chemical waste so that they can be recycled or dis-
posed of in an environmentally friendly manner.

English