Telefunken TF-AS1203UB - Инструкция по эксплуатации - Страница 5

4

Instruction manual

5

position to switch the power on; the unit will 

go into standby mode. Press STBY/MODE 
button on the panel or STANDBY button on the 
RC to switch the unit from standby mode; the 
backlight on the front panel will light up. To turn 
the unit to standby mode press and hold STBY/
MODE button on the panel or press STANDBY 
button on the RC. To switch the power off, slide 
POWER switch to OFF position.

Clock setting

• In standby mode press CLOCK button on

the RC or press SLEEP/CLOCK button on the 
panel to enable time setting mode. Hour digits 
will blink; press repeatedly 

/

 buttons to 

set hours. Press CLOCK button on the RC 
or SLEEP/CLOCK button on the panel again; 
minute hours will blink. Press repeatedly 

/

buttons to set minutes. Press CLOCK button 
on the RC or SLEEP/CLOCK button on the 
panel to confirm the time.

• In time setting mode, if no button is pressed

within 5 seconds, the unit will automatically go 
to clock mode.

AUX input

You can connect the audio output of an 

external device to this unit, to listen to the sound 
of that device through the speakers of this unit.

• To connect an external audio device,

please use a standard audio cable with 3.5-mm-
to-3.5 mm plugs to connect the headphone out 
or audio line-out of the external device to the 
AUX input socket of this unit.

• Press repeatedly MODE button on the RC

or STBY/MODE button on the panel to select 
LINE mode; LINE will be displayed.

• Turn on the external device. You cannot

control playback with the buttons of this unit 
except adjusting the volume.

Volume

Press VOL+/ALARM2 and VOL-/ALARM1 

buttons on the panel or +/- buttons on the RC 
to adjust the sound volume level. Press MUTE 
button on the RC to mute the sound, press this 
button again to resume the sound.

Equalizer

Press EQ button repeatedly to select an 

equalizer mode: ROCK/CLASS/FLAT/POP/
JAZZ.

Modes

Press MODE button on the RC or STBY/

MODE button on the panel repeatedly to select 
an operation mode: external audio device from 
the line input (LINE) => FM radio => USB => 
SD. USB and SD modes are available only if 
corresponding storage is connected.

Display backlight

Press DIMMER button on the RC repeat--

edly to change the display backlight brightness 
level.

Radio operation

• Press MODE button on the RC or STBY/

MODE button on the panel repeatedly to select 
radio mode.

• For FM reception extend the wire antenna.
• To adjust the frequency step by step

press repeatedly 

/

 buttons. For automatic 

search of a station, press and hold 

 or 

 button; the unit will look for the next 

available station and start its broadcast. 
Repeat the operation to search more stations. 
Press SELECT/SCAN button on the RC to 
automatically search available stations.

• To save a station, press PRESET button

on the RC or press and hold  /PRESET 
button on the panel. The memory position 
will blink. Press P+/P- buttons to select a 
memory position. Press PRESET ( /PRESET) 
button again to save the current station under 
the selected number. You can maximum 20 
stations in the memory. 

  To input a position number for saving 

or a stored station number you can also press 
number buttons on the RC (1, 2, 3, 4, 5 buttons 
for corresponding numbers and SHIFT+1, 
SHIFT+2, SHIFT+3, SHIFT+4, SHIFT+5 to 
input 6, 7, 8, 9, 0 correspondingly).

• To call a saved station, press P+/P- buttons.