KARCHER K4 Basic Car 1.180-083 - Инструкция по эксплуатации - Страница 12

– 7

ATTENTION

Dry running of more than 2 minutes leads to damage of 
the high-pressure pump. If the appliance does not build 
up pressure within 2 minutes, switch the appliance off 
and proceed in accordance with the instructions in 
Chapter "Troubleshooting".

Illustration 



Push the high pressure hose into the quick cou-
pling until it locks audibly.

Note:

 Make sure the connection nipple is aligned 

correctly.



Check the secure connection by pulling on the high 
pressure hose.



Attach the water supply hose to the coupling on the 
water connection.

Note:

 The supply hose is not included.



Connect the water supply hose to the water supply.



Completely open the water tap.



Insert the mains plug into the socket. 



Turn on the appliance “I/ON”.



Unlock the lever on the trigger gun.



Pull on the lever of the trigger gun; the device will 
switch on.
Let the appliance work until the water exits at the 
hand spray gun without bubbles (max. 2 minutes).



Release the lever on the trigger gun.

Note:

 Release the lever of the trigger gun; the de-

vice will switch off again. High pressure remains in 
the system.



Lock the lever on the trigger gun.

몇

CAUTION

Keep a distance of at least 30 cm when using the jet for 
cleaning painted surfaces to avoid damage.

ATTENTION

Car tyres, paint or sensitive surfaces such as wood 
should not be cleaned with the dirt blaster, as there is a 
risk of damage.

Illustration 



Push the spray lance into the trigger gun and fasten 
it by turning it through 90°.



Unlock the lever on the trigger gun.



Pull on the lever of the trigger gun; the device will 
switch on.

ATTENTION

Risk of damage to the paintwork
When working with the washing brush, it must be free of 
dirt or other particles.



Push the washing brush into the trigger gun and 
fasten it by a 90° turn.

Note

: If required, the washing brushes can be used to 

work with detergent.



DANGER

When using detergents, the material data safety sheet 
issued by the detergent manufacturer must be adhered 
to, especially the instructions regarding personal pro-
tective equipment.

Note:

 Detergent can only be added when the device is 

operated in low pressure mode.
Illustration 



Pull detergent suction hose as far as is required out 
of the housing.



Suspend end of detergent suction hose in a con-
tainer filled with detergent.



Use spray lance with pressure regulation (Vario 
Power).



Turn the spray lance as far as it will go in the direc-
tion of "SOFT".

Note:

 This will mix the detergent with the water 

stream.



Spray the detergent sparingly on the dry surface 
and allow it to react, but not to dry.



Spray off loosened dirt with the high pressure jet.



Release the lever on the trigger gun.



Lock the lever on the trigger gun.



During longer breaks (more than 5 minutes), also 
turn the appliance off using the "0/OFF" switch.

몇

CAUTION

Only separate the high-pressure hose from the trigger 
gun or the appliance when there is no pressure in the 
system.



After operation with detergent: Run the machine for 
approximately 1 minute for a clear rinse.



Release the lever on the trigger gun.



Turn off the appliance "0/OFF".



Turn off tap.



Press the lever on the trigger gun to release any re-
maining pressure in the system.



Lock the lever on the trigger gun.



Disconnect the mains plug from the socket.



Detach the appliance from the water supply.

몇

CAUTION

Risk of personal injury or damage! 
Mind the weight of the appliance during transport.

Illustration 



Pull out the transport handle until it audibly snaps 
into place.



Pull the appliance by its transport handle.



Secure the appliance against shifting and tipping 
over.

Start up

Operation

Operation with washing brush

Working with detergent

Recommended cleaning method

Interrupting operation

Finish operation

Transport

When transporting by hand

When transporting in vehicles

12

EN