Karcher K 7 Full Control *EU 1.317-000.0 - Инструкция по эксплуатации - Страница 15

– 9



DANGER

Risk of electric shock.



Prior to all work on the appliance, switch off the ap-
pliance and pull the power plug.

Clean the sieve in the water connection regularly.



Remove coupling from the water connection.

ATTENTION

The sieve must not be damaged.

Illustration 



Pull the sieve out using flat pliers.



Clean the sieve under running water.



Reinsert the sieve into the water connection.

The batteries are depleted if nothing is shown on the 
display of the trigger gun anymore.
Two batteries or accumulators of the size AAA are re-
quired.
Illustration 



Push the locking slide.



Open battery compartment.



Remove the batteries.
Dispose of the used batteries according to the local 
provisions.



Insert new batteries and observe the correct orien-
tation of the terminals.



Close battery compartment.



DANGER

Risk of electric shock. Turn off the appliance and remo-
ve the mains plug prior to performing any care and 
maintenance work.
Repair work and work on the electrical components may 
only be performed by an authorised customer service.

You can rectify minor faults yourself with the help of the 
following overview. 
If in doubt, please consult the authorized customer ser-
vice.



Push the lever of the trigger gun, the device will 
switch on.



Check whether the voltage indicated on the type 
plate corresponds to the voltage of the mains sup-
ply.



Check the mains connection cable for damages.



Motor overloaded, the motor circuit breaker has 
tripped.

–

Turn off the appliance "0/OFF".

–

Allow the device to cool down for 

one hour

.

–

Switch on the device and put it into operation again.
If the malfunction occurs repeatedly, have the de-
vice checked by the customer service.

Voltage reduction due to weak mains supply or when 
using an extension cable.



Upon switch-on, push the lever of the trigger gun 
first and then switch the power switch to "I/ON".



Check setting at the spray lance.



Check water supply for adequate delivery rate.



Pull out the sieve in the water connection using flat-
nose pliers and clean under running water.



Remove air from appliance before operation.
Switch on the appliance without connection the HP 
hose (max. 2 minutes) and run it until the water di-
scharging from the HP outlet is free of bubbles. 
Switch off appliance and reconnect HP hose.



Clean high-pressure nozzle: Remove dirt and deb-
ris from the nozzle bore, using a needle and rinse 
through with water from the front.



Check water flow quantity.



Dropwise leakage of the device is normal for tech-
nical reasons. If the leakage increases contact the 
authorized customer service.



Use Vario Power spray lance.
Turn the spray lance to "Mix" position.



Check whether the Plug 'n' Clean detergent bottle 
is placed into the detergent connection facing 
down.



Check / replace the batteries

Use only original KÄRCHER spare parts. You will find a 
list of spare parts at the end of these operating instruc-
tions.

The warranty terms published by the relevant sales 
company are applicable in each country. We will repair 
potential failures of your appliance within the warranty 
period free of charge, provided that such failure is 
caused by faulty material or defects in manufacturing. In 
the event of a warranty claim please contact your dealer 
or the nearest authorized Customer Service centre. Ple-
ase submit the proof of purchase.
Addresses can be found under:

www.kaercher.com/dealersearch

Care and maintenance

Clean the sieve in the water connection

Changing the batteries of the trigger gun

Troubleshooting

Appliance is not running

Appliance does not start, motor hums

Pressure does not build up in the appliance

Strong pressure fluctuations

Appliance is leaking

No detergent infeed

No pressure indicator on the trigger gun

Spare parts

Warranty

15

EN