Мойки высокого давления Karcher K 2.400 1.674-100 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
– 7
Mount loose parts delivered with appliance prior
to start-up.
Illustrations on Page 3
Illustration
Insert the transport wheels and lock them.
Illustration
Attach the transport handle /carrying handle.
Illustration
Fasten the quick coupling for the high pres-
sure hose to the high pressure connection.
Illustration
Push the high pressure hose into the trigger
gun until it locks audibly.
Note:
Make sure the connection nipple is
aligned correctly.
Check the secure connection by pulling on
the high pressure hose.
Optional
Illustration
Pull the suction hose for detergent through
the cover of the detergent tank until the filter
contacts teh bottom of the tank.
Close the detergent tank with the lid.
Lock the detergent tank in place on the appli-
ance.
Illustration
Hook the accessories net into the hooks
shown in the illustration.
According to the applicable regula-
tions, the appliance must never be
used on the drinking water supply with-
out a system separator. Use a suitable
system separator manufactured by KÄRCHER;
or, as an alternative, a system separator as per
EN 12729 Type BA. Water flowing through a sys-
tem separator is considered non-drinkable.
Caution
Always connect the system separator to the wa-
ter supply, never directly to the appliance!
Note:
Impurities in the water can damage the
high-pressure pump and accessories. For pro-
tection, the use of the KÄRCHER water filter (op-
tional accessory, order no. 4.730-059) is
recommended.
Observe regulations of water supplier.
For connection values, see type plate/technical
data.
Use a fibre-reinforced water hose (not in-
cluded) with a standard coupling. (Minimum
diameter 1/2 inch (13 mm), minimum length
7.5 m).
Illustration
Screw the supplied coupling element to the
water connection on the appliance.
Push the water supply hose onto the cou-
pling unit, then connect it to the water supply.
Caution
Dry runs lasting longer than two minutes lead to
damages to the high pressure pump. If the appli-
ance does not build up pressure within two min-
utes, switch it off and proceed as instructed in
the Chapter "Troubleshooting".
Illustration
Insert the high pressure hose tightly into the
quick coupling on the appliance, it will lock in
audibly.
Note:
Make sure the connection nipple is
aligned correctly.
Check the secure connection by pulling on
the high pressure hose.
Illustration
Push the spray lance into the trigger gun and
fasten it by turning it through 90°.
Completely open the water tap.
Insert the mains plug into the socket.
Turn on the appliance “I/ON”.
몇
Danger
The trigger gun is subjected to a recoil force
when the water jet is discharged. Make sure that
you have a firm footing and are also holding the
trigger gun and spray lance firmly.
Illustration
Unlock the lever on the trigger gun.
Pull on the lever of the trigger gun; the device
will switch on.
Note:
Release the lever of the trigger gun; the
device will switch off again. High pressure re-
mains in the system.
Carrying out the most common cleaning tasks.
The work pressure can be stagelessly regulated
between "Min" and "Max". You can add deter-
gent when "Mix" is selected.
Release the lever on the trigger gun.
Illustration
Turn the spray pipe to the desired position.
Before Startup
Water supply
Water supply from mains
Start up
Operation
Spray lance with pressure regulation (Vario
Power)
14
EN
