Bort BHR-2100 - Инструкция по эксплуатации - Страница 6

6

ter to clear off any dirt or grime that may have collected 
on the surface. This will allow your detergent to attack 
the deep down dirt that has worked its way into the 
cleaning surface. Before triggering the gun, adjust the 
nozzle to a wide fan pattern and slowly adjust to the 
desired spray pattern. This will help you avoid apply-
ing too much concentrated spray to the surface which 
could cause damage.

3. Detergent Application

USE THE INSTRUCTIONS APPROPRIATE
FOR MODEL PURCHASED

NOTE:

 Use only detergents formulated for pressure 

washes.

NOTE:

 Test detergent in an inconspicuous area before 

use.

Figure 7 - Detergend application

UNITS WITH DETERGENT APPLICATOR 
INCLUDED

Follow manufacturer’s label directions for mixing cor-
rect concentrations of detergent to water ratio through 
the pressure washer is approximately 5.4% (1 to 19).
1.  Unscrew to top of detergent applicator and 

fi

 ll  ap-

plicator with detergent.

2. Replace top on applicator.
3. Remove lance from gun.
4. Attach detergent applicator to gun. ( See Figure 8)

Figure 8 - Attach applicator to gun

5. Apply detergent so it thoroughly covers cleaning 
surface. Apply from bottom to top to prevent detergent 
from sliding down and streaking.
6. Allow detergent to remain on the surface for a few 
minutes. This is a good time to use a brush to lightly 
scrub heavily soiled areas.
Never allow detergent to dry on the cleaning surface.
7. Remove detergent applicator from gun and replace 
with the lance, or remove applicator from end of lance.
8. Rinse detergent from surface.

NOTE:

 Flush detergent applicator with clear water fol-

lowing each use.

4. Final Rinse

Start 

fi

 nal rinse at bottom an work upward. Make sure 

you thoroughly rinse the surface and that all detergent 
has been removed.

5. Shut down 

1. Be sure all detergent is 

fl

 ushed from system.

2. Turn off motor.
3. Turn off water supply.
4.  After motor and water supply are turned off, trigger 

gun to depressurize system.

CAUTION:

 NEVER turn water supply off before turn-

ing motor off. Serious damage could occur to the pump 
and or motor.

WARNING!

 NEVER disconnect high pressure dis-

charge hose from machine while system is pressur-
ized. To depressurize, turn motor off, turn water supply 
off and squeeze gun trigger 2-3 times.
5.  After each use, wipe all surfaces of the pressure 

washer with a clean, damp cloth.

6. Storage  

Do not store pressure washer outdoors.
Do not store pressure washer where it might freeze.

TIPS FOR EXTENDING THE LIFE
OF YOUR PRESSURE WASHER
1. Never operate unit without water.
2.  Pressure washer is not meant to pump hot water. 

Never connect to hot water supply – this will signi

fi

 -

cantly reduce life of the pump.

3.  Using detergent other than others brand may cause 

damage to pump components (o-rings, etc.).This 
also applies to chemicals such as bleach, dish soap, 
etc.

4.  Never operate unit for more than one (1) minute 

without spraying water. Resulting heat buildup will 
damage pump.

5.  Before adjusting nozzle’s pressure (high-to-low or 

low-to-high) release trigger. Failure to do so will re-
duce life of o-rings in lance.

THE SUCTION FUNCTION

You can connect the high pressure cleaner to the water 
sources such as taps or pump water from other sourc-
es without pressure.
To work with the water supply without pressure the suc-
tion hose should be removed from the supply and the 
gun nozzle should be moved to position “Low” (Figure 
14). After that the high pressure cleaner should work 
idle for a few seconds to drain the excess water and 
release air.  Put the suction hose into the water source. 
After draining some water the gun nozzle should be 
moved to position “High” (Figure 14). Now the high 
pressure cleaner is ready to work under high pressure.

TROUBLESHOOTING

1. When switched on, the machine will not start 
working.

●

  Plug is not well connected or electric socket is faulty.

  -  Check plug, socket and fuse.

●

  The mains voltage is lower than the minimum re-

quirement for start up.

  Check that the mains voltage is adequate.

●

  The pump is stuck.

  -  Refer to after storage instructions. Switch off the 

unit and let the motor cool.