Bort BHR-2000-Smart - Инструкция по эксплуатации - Страница 9

9

peratures from 0 ° C to +40 ° C with a relative humidity of 
not more than 80% .

Transportation:

It is strongly prohibited dropping and any mechanical im-
pact on the packaging during transportation .
When unloading / loading, it is not allowed to use any 
type of equipment that works on the principle of packing 
clamping .

SAFETY INSTRUCTIONS

When using electric machines always observe the safe-
ty regulations applicable in your country to reduce the 
risk of fire, electric shock and personal injury . Read the 
following safety instructions and also the enclosed 
safety instructions .
Keep these instructions in a safe place!

Electrical safety

Always check if your mains voltage corresponds with 
the value on the type plate .
When replacing old cables or plugs: throw away old 
cables or plugs immediately as soon as new ones have 
replaced these . It is dangerous to put the plug of a 
loose cable into the socket outlet .
When using extension cables:
Only use an approved extension cable that is suitable 
for the machine’s power . The cores must have a diame-
ter of at least 1 .5 mm2 . When the extension cable is on 
a reel, unroll the cable in its entirety .
All electrical connections e .g . extension cable, must 
be of an approved waterproof type for outdoor use 
and marked accordingly . Extension cables must be 
threecore, one of which is EARTH .

Switch off the machine immediately in case of:

9 .  Malfunction in the mains plug, power cable or dam-
aging of cable .
10 . Broken switch .
11 . Smoke or stench of scorched insulation .

Specific safety rules

•  Do not disconnect the plug by pulling on the elec-
trical cable .
•  If you are too far from the object you wish to clean, 
do not move the cleaner nearer by pulling on the high 
pressure hose; use the handle provided .
•  Do not obstruct the ventilation grilles during opera-
tion .
•  The cross-section of any extension cables used must 
be proportional to their length, i .e . the longer the ex-
tension cable, the greater the cross-section; cables with 
a protection level of “IPX5” must be used .
•  Position the high pressure

cleaner AS NEAR POSSIBLE 

to the water supply .

•  Use the high pressure

cleaner only with accessories 

and replacement parts authorized by the manufacturer . 
The use of original accessories and replacement parts 
will ensure safe, trouble-free operation .
•  Avoid unintentional firing of the trigger . Do not carry 
the lance / trigger assembly with your hand over the 
trigger . Always use the trigger lock mechanism .
•  Ensure that the safety lock on the trigger is used, 
when you have stopped using the pressure washer to 
prevent accidental operation .
•  Do not use the cleaner with inflammable or toxic liq-
uids, or any products which are not compatible with the 
correct operation of the high pressure

cleaner .

•  Do not direct the water jet towards the unit itself, 
electrical parts or towards other electrical equipment .
•  Do not allow children or incompetent persons to use 
the high pressure

cleaner .

•  Do not touch the plug and/or socket with wet hands .
•  Do not use the high pressure

cleaner if the electrical 

cable is damaged .
•  Do not use the high pressure

cleaner if the high pres-

sure hose is damaged .
•  Do not jam the trigger in the operating position .
•  Check that the data plates are affixed to the high 
pressure

cleaner, if not, inform your dealer . Cleaners 

without plates must NOT be used as they are unidenti-
fiable and potentially dangerous .
•  Do not tamper with or alter the calibration of the safe-
ty valve .
•  Do not alter the original diameter of the spray head 
nozzle .
•  Do not leave the high pressure

cleaner unattended .

•  Do not move the high pressure

cleaner by pulling on 

the electrical cable .
•  All electrical conductors MUST BE PROTECTED against 
the water jet .
•  The high pressure cleaner MUST ONLY BE CONNECT-
ED to a correctly earthed power supply .
•  The high pressure may cause materials to bounce off 
surfaces at speed; therefore protective clothing and 
safety goggles MUST BE WORN .
•  Before doing work on the cleaner, REMOVE the plug .
•  Before pressing the trigger, GRIP the gun firmly to 
counteract the recoil .
•  Maintenance and/or repair of electrical components 
MUST be carried out by qualified staff .
•  DISCHARGE residual pressure before disconnecting 
the high pressure

cleaner hose .

•  Before using the high pressure

cleaner, CHECK every 

time that the screws are fully tightened and that there 
are no broken or worn parts .
•  Only USE detergents which will not corrode the coat-
ing materials of the high pressure hose/electrical cable
•  ENSURE that all people or animals keep a minimum