BORT BPS-500-P - Инструкция по эксплуатации - Страница 8

8

bind and are easier to control.

•  Use the power tool, accessories and tool bits etc. in 

accordance with these instructions, taking into account 
the working conditions and the work to be performed. 
Use of the power tool for operations diferent from 
those intended could result in a hazardous situation.

Service

Have your power tool serviced by a qualiied repair person 
using only identical replacement parts. This will ensure 
that the safety of the power tool is maintained.

SAFETY WARNINGS FOR JIGSAWS

•  Keep hands away from the sawing range. Do not reach 

under the workpiece. Contact with the saw blade can 
lead to injuries.

•  Apply the machine to the workpiece only when 

switched on. Otherwise there is danger of kickback 
when the cutting tool jams in the workpiece.

•  Pay attention that the base plate securely on the mate-

rial while sawing. A jammed saw blade can break or lead 
to kickback.

•  When the cut is completed, switch of the machine and 

then pull the saw blade out of the cut only after it has 
come to a standstill. In this manner you can avoid kick-
back and can place down the machine securely.

•  Use only undamaged saw blades that are in perfect 

condition. Bent or dull saw blades can break, negatively 
inluence the cut, or lead to kickback.

•  Do not brake the saw blade to a stop by applying side 

pressure after switching of. The saw blade can be dam-
aged, break or cause kickback.

•  Use suitable detectors to determine if utility lines are 

hidden in the work area or call the local utility company 
for assistance. Contact with electric lines can lead to 
ire and electric shock. Damaging a gas line can lead 
to explosion. Penetrating a water line causes property 
damage or may cause an electric shock.

•  Secure the workpiece. A workpiece clamped with 

clamping devices or in a vice is held more secure than 
by hand.

•  Always wait until the machine has come to a complete 

stop before placing it down. The tool insert can jam and 
lead to loss of control over the power tool.

•  Before any work on the machine itself, pull the mains 

plug.

•  Clean the shank of the saw blade before inserting it. An 

unclean shank cannot be fastened securely.

•  Check the tight seating of the saw blade. A loose saw 

blade can fall out and lead to injuries.

•  The saw blade should not be longer than required for 

the intended cut. Use a narrow saw blade when sawing 
tight curves.

•  If the saw blade is wedged or jammed when removing, 

press the saw blade holder lightly toward the front (ap-
prox. 2 mm).

•  Dusts from materials such as lead-containing coatings, 

some wood types, minerals and metal can be harmful 
to one’s health and cause allergic reactions, lead to res-
piratory infections and/or cancer. Materials containing 
asbestos may only be worked by specialists.

•  As far as possible, use a dust extraction system suitable 

for the material.

•  Provide for good ventilation of the working place.
•  It is recommended to wear a P2 ilter-class respirator.
•  Observe the relevant regulations in your country for the 

materials to be worked.

•  Prevent dust accumulation at the workplace. Dusts can 

easily ignite.

•  Observe correct mains voltage! The voltage of the power 

source must agree with the voltage speciied on the 
nameplate of the machine. Power tools marked with 230 
V can also be operated with 220 V.

•  To save energy, only switch the power tool on when 

using it.

•  The contact protector attached to the casing prevents 

accidental touching of the saw blade during the work-
ing procedure and may not be removed.

•  Before sawing in wood, particle boards, building materi-

als etc., check for foreign objects, such as nails, screws, 
etc. and remove them as required.

•  Plunge cuts may only be applied to soft materials, such 

as wood, gypsum board, etc. For plunge cuts, use only 
short saw blades.

•  The sliding shoe can prevent the surface from being 

scratched. The splinter guard can prevent fraying of 
the surface while sawing wood. Do not use the splinter 
guard for mitre cuts.

•  Adapt the settings of your power tool to the respective 

application. For example, reduce the stroke rate and or-
bital action when cutting metal or for tight curved cuts.

•  For long and straight cuts in thick wood (>40 mm), the 

cutting line can become inaccurate. In this case, using a 
circular saw is recommended to achieve accurate cuts.

•  In extreme conditions, always use dust extraction as far 

as possible. Blow out ventilation slots frequently and 
install a portable residual current device (PRCD). When 
working metals, conductive dust can settle in the inte-
rior of the power tool. The total insulation of the power 
tool can be impaired.

MAINTENANCE AND CLEANING

Make sure that the machine is not live when carry-
ing out maintenance work on the motor.

•  Regularly clean the machine housing with a soft cloth, 

preferably after each use. Keep the ventilation slots free 
from dust and dirt.If the dirt does not come of use a soft 
cloth moistened with soapy water. Never use solvents 
such as petrol, alcohol, ammonia water, etc. These sol-
vents may damage the plastic parts.

•  Lubricate the guide roller occasionally with a drop of oil.
•  Should a fault occur, e.g. after wear of a part, please 

contact your local BORT GLOBAL LIMITED dealer.

DISPOSAL

Discarded electric appliances are recyclable and 
should not be discarded in the domestic waste! 
Please actively support us in conserving resources 
and protecting the environment by returning this 

appliance to the collection centres (if available).
In order to prevent the machine from damage during