Котел Kospel EKCO.L1 36 z - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
1 609 92A 01G | (9.1.13)
Bosch Power Tools
14
| English
Maintenance Schedule
Clean the magazine
12
. Remove any plastic or wood chips
that may accumulate in the magazine during operation.
Clean the power tool in regular intervals using compressed
air.
Correction of Malfunctions
Measure
Explanation
Action
Cleaning the magazine
12
and magazine slider
13
.
Prevents the jamming of nails.
– Blow out the mechanism of the magazine/magazine slider
daily with compressed air.
Ensuring that the discharge lock-off
2
functions properly.
Promotes your work safety and efficient use of the power
tool.
– Blow out the mechanism of the discharge lock-off daily with
compressed air.
Problem
Cause
Corrective Measure
The machine is not operative.
The battery is discharged or defective.
– Fully recharge the battery or exchange it.
The battery is not properly inserted.
– Make sure that the battery has engaged properly in the han-
dle.
The battery temperature is too high or too low.
– Wait until battery has reached the optimal operating tem-
perature again.
The battery contacts are contaminated/dirty or defective. – Contact an authorised service agent for Bosch power tools.
Have the component replaced there.
The actuation system is blocked.
– Press switch
5
toward the right to disengage the actuation
system.
The magazine
12
is empty.
– Refill the magazine.
(See “Loading the Magazine”, page 12)
The discharge lock-off
2
is bent.
– Contact an authorised service agent for Bosch power tools.
Have the component replaced there.
The electronic system is defective.
– Contact an authorised service agent for Bosch power tools.
The power tool is ready for operation, but no nails are dis-
charged.
The following components may be faulty:
– Trigger
6
– Driver blade
– Motor or drive belt
– Electronic system
– Contact an authorised service agent for Bosch power tools.
Have the component replaced there.
Foreign objects have accumulated in the shot mecha-
nism.
– Contact an authorised service agent for Bosch power tools.
Have the component replaced there.
Foreign objects have accumulated in the outlet
15
or in
the magazine
12
.
– Clean the outlet
15
or the magazine
12
.
A nail is jammed in the shot duct.
– Clear the jam.
(See “Clearing Jams”, page 13)
The magazine slider is
13
defective.
– Clean the magazine slider
13
as required and make sure that
the magazine
12
is not dirty/soiled.
The spring of the magazine slider is too week or defective. – Contact an authorised service agent for Bosch power tools.
Have the component replaced there.
The fasteners being used are not permitted.
– Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in table
“Technical Data” may be used.
The magazine
12
is empty.
– Refill the magazine.
(See “Loading the Magazine”, page 12)
The nails are driven in too deep.
The depth stop is set too deep.
– Adjust the depth stop to the desired depth.
(See “Adjusting the Depth Stop”, page 13)
The buffer is worn.
– Contact an authorised service agent for Bosch power tools.
Have the component replaced there.
The nails are not driven in deep enough.
The battery is discharged or defective.
– Fully recharge the battery or exchange it.
The fasteners are too long.
– Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in table
“Technical Data” may be used.
The depth stop is set too high.
– Adjust the depth stop to the desired depth.
(See “Adjusting the Depth Stop”, page 13)
The power tool skips nails or has a too large cycle feed.
The fasteners being used are not permitted.
– Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in table
“Technical Data” may be used.
The spring of the magazine slider is too week or defective. – Contact an authorised service agent for Bosch power tools.
Have the component replaced there.
Frequent jamming of nails in the shot duct.
The fasteners being used are not permitted.
– Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in table
“Technical Data” may be used.
– Contact an authorised service agent for Bosch power tools.
The driven nails are bent.
The driver blade is damaged.
– Contact an authorised service agent for Bosch power tools.
Have the component replaced there.
OBJ_BUCH-1335-004.book Page 14 Wednesday, January 9, 2013 1:22 PM
